Arcan ALJ3T User Manual

ALJ3T © 2007 Arcan Tools 1 rev. 02/26/07
Study, underStand, and follow all inStructionS
before operating thiS device. do not exceed the rated
capacity. uSe only on hard level Surface. lift only on
areaS of the vehicle aS Specified by the manufacturer.
immediately after lifting, Support the vehicle with
appropriate meanS.
do not move or dolly the vehicle while on the jack.
failure to heed theSe markingS may reSult in perSonal
injury and/ or property damage. thiS iS a lifting device
only.
no alterationS Shall be made to thiS product.
THIS OPERATING MANUAL CONTAINS
IMPORTANT SAFETY INFORMATION.
READ CAREFULLY AND UNDERSTAND
ALL INFORMATION BEFORE
OPERATING TOOL.
SAVE THIS MANUAL FOR FUTURE USE.
FOR YOUR SAFETY AND TO PREVENT INJURY:
Use Service Jack for
lifting purposes
ONLY.
Always support
vehicle with
jack stands.
ALJ3T
3 TON CApACiTy ALumiNum serviCe JACk
pArTs BreAkDOWN AND OperATiNG mANuAL
IMPORTANT: if you have any problems or concerns with our product, please call 1-800-879-7316 (toll-free)
for immediate assistance. Please do not call the store where you purchased this product.
PRIOR TO OPERATION
Air may become trapped in the hydraulic system during transit.
To purge air:
1. Open release valve by turning handle counterclockwise.
2. Pump handle rapidly 4 full strokes. This will expel air that
may have entered hydraulic fluid passages during transit.
3. Close release valve by rotating handle clockwise and
pump handle.
4. If lift arm raises to full height, jack is ready for use.
If not, repeat this procedure or follow trouble shooting
instructions provided.
MAINTENANCE AND INSPECTION
IMPORTANT: When adding or replacing hydraulic fluid, always
use a quality hydraulic fluid. DO NOT use brake fluid, alcohol,
glycerin, detergent motor oil, or dirty oil as improper fluid can
cause serious internal damage to jack.
To add hydraulic fluid: With saddle fully lowered and jack on
level ground, remove filler plug. The hydraulic fluid should just
cover the surface of the internal cylinder visible through the hole.
Do not overfill. Replace filler plug. If low, add hydraulic fluid
as needed.
Maintenance and Inspection: The owner and/or user
must maintain and inspect the jack in accordance with the
manufacturer’s instructions.
SPECIFICATIONS:
Net Weight: 26.3kg (58lbs)
Lifting Range: 9.7cm to 46cm (3.77in – 18.11in)
Overall Length: 67cm (26.37in)
Overall Width: 33cm (13in)
Min Height: 9.67cm (3.77in)
Max Height: 46cm (18.11in)
Saddle Diameter: 11.5cm (4.52in)

Arcan ALJ3T Specifications

General

Brand	Arcan
Model	ALJ3T
Category	Jacks
Language	English

Summary

Prior to Operation

Purging Air from Hydraulic System

Steps to remove trapped air from the hydraulic system during transit to ensure proper operation.

Maintenance and Inspection

Adding Hydraulic Fluid

Instructions for adding hydraulic fluid, specifying fluid type and correct level to prevent damage.

User Maintenance Responsibility

Highlights the owner's duty to maintain and inspect the jack according to manufacturer guidelines.

Safety Warnings and Operating Instructions

General Operation Safety

Critical safety information including reading manual, understanding operation, and following all instructions.

Lifting Safety Precautions

Essential safety rules for lifting, such as using on hard level surfaces and supporting with jack stands.

Specifications

Replacement Parts

Warranty Information

Owner/User Responsibility

Lubrication

Operating Instructions

Raising and Lowering Load

Detailed steps for safely raising and lowering a vehicle, including jack stand placement.

Proper Storage

Recommendations for storing the jack in a dry location on a level surface.

Troubleshooting

Jack Performance Issues

Guides to diagnose and solve common problems like the jack not lifting or leaking down.