Arctic APL71012BDW0 - User Manual

Questions and Answers

C
Carolyn ElliottSep 3, 2025
Why is the colour of the clothes faded after washing in my Arctic APL71012BDW0 Washer?
- C
  Courtney MccarthySep 3, 2025
  If the color of your clothes faded after washing in your Arctic Washer, it could be because: * Excessive laundry was loaded in, so do not load the machine in excess. * The detergent in use is damp, so keep detergents closed in a humidity-free environment and avoid excessive temperatures. * A higher temperature was selected, so select the proper programme and temperature according to the type and soiling degree of the laundry.
J
James RichardSep 2, 2025
Why is my Arctic APL71012BDW0 Washer washing performance poor and stains persist?
- M
  Meagan JohnsonSep 2, 2025
  If your Arctic Washer's washing performance is poor and stains persist, consider the following: * Use the recommended amount of detergent. * Do not overload the machine. * Select the proper programme and temperature. * Use original detergent appropriate for the machine. * Put the detergent in the correct compartment.
S
shepherdjimmyAug 31, 2025
Why is my Arctic Washer washing performance poor and laundry turns gray?
- C
  Carlos StephensAug 31, 2025
  If your Arctic Washer's washing performance is poor and laundry turns gray, it could be due to: * Insufficient detergent used over a long period, so use the recommended amount. * Washing at low temperatures for too long, so select the proper temperature. * Insufficient detergent with hard water, so use an adequate amount. * Too much detergent is used, so use the recommended amount.
E
Elizabeth SchneiderAug 29, 2025
What to do if my Arctic APL71012BDW0 Washer program does not start after closing the door?
- T
  tylerwalterAug 29, 2025
  If the program on your Arctic Washer doesn't start after closing the door: * Ensure the Start / Pause / Cancel button was pressed. If not, press it. * If the loading door is hard to close, you may have overloaded the machine. Reduce the amount of laundry and ensure the door is properly closed.
B
brian87Aug 28, 2025
Why does my Arctic Washer machine not switch to the spinning step?
- J
  Jennifer DouglasAug 28, 2025
  Your Arctic Washer might not switch to the spinning step because: * There might be an unbalanced load, so the automatic unbalanced load detection system might be activated. * The machine will not spin if water is not drained completely, so check the filter and the draining hose. * Excessive foam might have occurred due to too much detergent, so use the recommended amount of detergent.
J
Jason WilkersonAug 26, 2025
Why is there too much foam forming in my Arctic APL71012BDW0?
- X
  xwalterAug 27, 2025
  Too much foam in your Arctic Washer can be caused by: * Using improper detergents, so use detergents appropriate for washing machines. * Using an excessive amount of detergent, so use only a sufficient amount. * Improper detergent storage, so store detergent in a closed and dry location. * Some meshed laundry may foam too much, so use smaller amounts of detergent for these items. * The detergent might be put in the wrong compartment, so put it in the correct one. * The softener is being taken early.
A
Andrew FrenchAug 25, 2025
What to do if the Arctic APL71012BDW0 loading door cannot be opened?
- C
  cbakerAug 25, 2025
  If the loading door of your Arctic Washer cannot be opened, it may be due to several reasons: * The door lock is activated because of the water level in the machine, so drain the water by running the Pump or Spin programme. * The machine is heating up the water or is at the spinning cycle, so wait until the programme completes. * The Child lock is engaged, so wait a couple of minutes for deactivation of the door lock. * The loading door may be stuck because of the pressure, so grab the handle and push and pull the loading door to release and open it. * Water pressure is low. * Voltage might be low. * Input temperature of water might be low. * Number of rinses and/or amount of rinse water might have increased.
W
Wesley SimsAug 23, 2025
What to do if the Arctic APL71012BDW0 Washer machine does not drain water?
- M
  martinezandreaAug 23, 2025
  If your Arctic Washer isn't draining water, the water drain hose might be clogged or twisted, so you should clean or flatten the hose. Also, the pump filter might be clogged, so clean the pump filter.

Summary

General Safety Instructions

Life and Property Safety

Safety instructions for product placement and usage to prevent injuries and material damage.

Electrical Safety

Precautions for safe electrical connections and usage to prevent electric shock.

Installation Guide

Appropriate Installation Location

Guidelines for selecting a suitable, stable, and safe location for the washing machine.

Removing Transportation Locks

Step-by-step guide to remove transportation safety bolts before operation.

Connecting Water and Power

Instructions for connecting water supply and electrical power safely.

Preparing for Wash

Detergent and Softener Usage

Guidance on selecting and using detergents, softeners, and other cleaning agents.

Operating the Washing Machine

Control Panel Overview

An overview of the washing machine's control panel, buttons, and indicators.

Programme and Consumption Details

Maintenance and Cleaning

Routine Cleaning Procedures

Draining and Pump Filter Care

Troubleshooting Common Issues

Program Start and Selection Problems

Water Intake and Drainage Issues

Washing Performance and Noise Problems

Specific Operational Errors

Arctic APL71012BDW0 Specifications

General

Washing Capacity	7 kg
Drying Capacity	4 kg
Maximum Spin Speed	1200 RPM
Energy Efficiency Class Washing	A
Energy Efficiency Class Washing & Drying	B
Spin Speed	1200 RPM
Dimensions (H x W x D)	85 x 60 x 54 cm
Color	White
Type	Front Load
Capacity	7 kg