arcweld TIG 201 AC/DC User Manual

IM7906-5
Apirl. 2015
Rev. 01
arcweld
®
TIG 201 AC/DC
For use with machine Part Number K69021-7, Code 76262
THE SHANGHAI LINCOLN ELECTRIC COMPANY
No. 195, Lane 5008, Hu Tai Rd. Baoshan, Shanghai, PRC 201907
www.lincolnelectric.com.cn
Copyright © 2015 The Shanghai Lincoln Electric Company
Safety Depends on You
arcweld
®
machine is designed and
built with safety in mind. However,
your overall safety can be increased
by proper installation and thoughtful
operation on your part. DO NOT
INSTALL, OPERATE OR REPAIR
THIS EQUIPMENT WITHOUT
READING THIS MANUAL AND
THE SAFETY PRECAUTIONS
CONTAINED THROUGHOUT. And,
most importantly, think before you
act and be careful.

arcweld TIG 201 AC/DC Specifications

General

Frequency	50/60 Hz
Protection Class	IP21S
Welding Process	TIG
Input Voltage	230V
Duty Cycle	60% @ 200A
Cooling Method	Air-cooled
Input Phase	1-Phase

Summary

SAFETY

Electric Shock Hazards

Describes dangers of electric shock.

Arc Ray Hazards

Covers protection from arc rays.

Electric and Magnetic Fields

Discusses EMF effects on pacemakers and operators.

Fumes and Gases

Details hazards from welding fumes and gases.

Welding Sparks

Explains fire and explosion risks from sparks.

Cylinder Safety

Addresses risks associated with gas cylinders.

Electromagnetic Compatibility (EMC)

EMC Conformance and Introduction

States compliance and describes emission sources.

Installation and Use Considerations

User responsibility for EMC and detecting disturbances.

Area Assessment for EMC

Factors to consider before installation.

Methods of Reducing Emissions

Techniques to minimize electromagnetic interference.

SUMMARY

General Introduction

Overview of the arcweld TIG 201 AC/DC welder.

Key Characteristics

Highlights features like arc start, stability, and safety.

Welding Capabilities

Lists supported welding processes and duty cycle.

INSTALLATION

Technical Specifications

Details electrical, physical, and temperature parameters.

Foot Pedal Setup

Explains foot pedal connections and function.

Parameter Presetting Ranges

Provides tables for various welding modes.

Installation Safety and Location

Warnings for installation, location, and input connections.

Generator Power Supply

Guidelines for operating with engine driven generators.

Output Cable Connections

How to connect cables for MMA and TIG welding.

TIG Welding (GTAW) Specifics

Instructions for TIG torch and gas connections.

HF Arc Start Precautions

Tips for effective high-frequency arc starting.

Operation Control and Connectors

Front Panel Controls and Display

Describes buttons, encoder, LEDs, and digital display.

Setting and Mode Selection

Steps for adjusting parameters and selecting modes.

MMA Operation Settings

Specific settings for Manual Metal Arc welding.

DC TIG Operation Settings

Specific settings for DC TIG welding.

DC TIG Welding Tables

Recommended settings for DC TIG on various materials.

DC TIG / Pulse Operation

Parameters and techniques for pulsed DC TIG.

DC TIG/Pulse Welding Tables

Parameter tables for pulsed DC TIG.

AC TIG Operation Settings

Settings for AC TIG welding.

AC TIG / Pulse Operation Settings

Parameters for AC TIG with pulse.

AC TIG / Pulse Welding Table

Parameter table for AC TIG/Pulse.

AC TIG / Mix & Spot Operation

Parameters for AC TIG/Mix and Spot welding.

Maintenance and Troubleshooting

Regular Maintenance Schedule

Daily, monthly, and yearly maintenance tasks.

Welding Defects and Prevention

Identifies common welding problems and their solutions.

How to Use Troubleshooting Guide

Explains the step-by-step process for using the guide.

Troubleshooting Common Issues

Lists problems, causes, and recommended actions.

Diagram

Internal Component Diagram

Illustrates the internal layout and components of the welder.