EasyManua.ls Logo

Argo AT2045 User Manual

Argo AT2045
36 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
INSTALLATION, OPER ATION
& MAINTENANCE MANUAL
An ISO 9001-2008 Certied Company
Information and specications outlined in this manual in effect at the
time of printing of this manual. ECR International, Inc. reserves the
right to discontinue, change specications or system design at any
time without notice and without incurring any obligation, whatsoever.
"AT" SERIES ELECTRIC
HOT WATER BOILERS
FOR FORCED HOT WATER
Manufactured by:
ECR International, Inc.
2201 Dwyer Avenue, Utica NY 13501
web site: www.ecrinternational.com
P/N# 240009740, Rev. A [09/2013]
Question and Answer IconNeed help?

Do you have a question about the Argo AT2045 and is the answer not in the manual?

Argo AT2045 Specifications

General IconGeneral
BrandArgo
ModelAT2045
CategoryBoiler
LanguageEnglish

Summary

Installation, Operation & Maintenance Manual

"AT" Series Boiler Dimensions

Important Safety Information

General Safety Precautions and Warnings

Details essential safety guidelines, hazard symbols, and critical warnings for installation and operation.

Introduction and Product Overview

Product Description and Capabilities

Explains the electric hydronic block, its operational theory, and key features.

Standard Control Features List

Enumerates the various functionalities and features of the boiler's control system.

Boiler Electrical Specifications and Voltage Ratings

Locating the Boiler and Clearance Requirements

Minimum Clearances to Combustible Constructions

Specifies the required minimum distances from the boiler to combustible materials.

Hydronic Piping System Design

Circulating System Design and Flow Rates

Guidance on circulating system design, including flow rates and temperature rise for different boiler sizes.

Connecting Supply and Return Piping

Instructions for connecting supply and return piping, including low water cutoff and backflow prevention.

Electrical Connections and Field Wiring

Boiler Wiring and Voltage Requirements

Details on the boiler's pre-wiring, voltage compatibility, and circuit breaker sizing.

Field Wiring Best Practices

Guidelines for field wiring, including wire types, strip length, and termination torque.

Thermostat and Control Wiring

Thermostat Installation and Wiring On Control

Instructions for thermostat placement and connecting pumps/thermostats to the control board.

Boiler Sequence of Operation

AT Boiler Controller Component Identification

Identifies and explains the function of each part of the AT Boiler Controller interface.

Setting Boiler Controller Parameters

Configuring Temperature Settings and Differentials

Guide to setting comfort heating, domestic hot water, and differential temperatures.

Boiler Display Codes and Fault Diagnostics

Understanding Boiler Display Codes

Explanation of various display codes indicating boiler status, modes, and temperature settings.

Interpreting and Resolving Fault Codes

Lists common fault codes, their causes, and required actions for troubleshooting.

Control Operation and Heating Cycles

Initial Startup and Two-Temperature Operation

Procedures for first-time boiler startup and operating dual temperature zones.

Heating Cycle Operation and Element Staging

Details the boiler's heating sequence, element staging, and temperature regulation.

Advanced Control Features and Inputs

Load Management and Flow Sensor Inputs

Information on connecting and utilizing Load Management (LMC) and Flow Sensor (FLO) inputs.

Low Water Cutoff and Pump Exercising Features

Explanation of Low Water Cutoff (LWCO) input and the pump exercising function.

Boiler Fault Codes and Test Mode

Detailed Fault Code Explanations

Comprehensive explanations for fault codes related to relays, sensors, power, and control hardware.

Installer Test Mode Functionality

Steps for entering and using the installer test mode for system verification and diagnostics.

Wiring Diagrams for 2-Element Boilers

Wiring Diagrams for 4-Element Boilers

Boiler Startup and Seasonal Maintenance

Placing the Hydronic Block into Service

Procedure for filling the heating system, purging air, and initial boiler activation.

General Boiler Maintenance Guidelines

Additional Wiring Diagrams: Single Zone with Circulator

Additional Wiring Diagrams: Multiple Zones

Modular Boiler Piping Configuration

Troubleshooting Boiler Issues

Diagnosing Noisy Boiler Operation

Steps to identify causes of noise and air in the hydronic system.

Procedure for Heating Element Replacement

Step-by-step instructions for safely replacing a heating element, including precautions.

AT Boiler Fault Troubleshooting Guide

Resistance vs. Temperature Reference Table

Parts List for 2 & 4 Element Boilers

Homeowner's Reference Table

Related product manuals