Argo IRO User Manual

V 01/19
31
Press this button to reduce to minimum the ventilation, for the most silence.
Note: The sleep mode cannot be started in ventilation mode.
(4) FAN SPEED ADJUSTMENT BUTTON
Press this button when the appliance is switched on for adjusting the ventilation speed in cooling mode (AUTO), to low
(Low), medium (Med) or high (High).
The fan speed cannot be adjusted in DRY mode and is fixed to low speed.
(5) TIMER BUTTON (on both the remote control and portable unit)
Press and hold this button for 1 second to set the timer.
1）Timer-on (automatic switch-on)
When the appliance is off, this button is used to set a delay after which the unit will switch on.
Remote control: press “TIMER” to set a time to turn on the air conditioner. Press +/- to set the time, and press
“TIMER” again to confirm it. The “G” icon will remain on to indicate that the TIMER has been set.
Portable unit: Press TIMER. Press Timer again to select a number of hours from 1 to 24. Press the TIMER button
to confirm.
2）Timer-off (automatic switch-off)
When the appliance is running in the COOL mode, set a delay after which the unit will switch off.
Remote control: press “TIMER” to set a time to turn on the air conditioner. Press +/- to set the time, and press
“TIMER” again to confirm it.. The “G” icon will remain lit to indicate that the switch-off TIMER is running.
Portable unit: Press TIMER. Press Timer again to select a number of hours from 1 to 24. Press the TIMER button
to confirm.
Resetting the timer: If a TIMER has been set, press TIMER to display the delay. Press TIMER again to cancel the
setting.
(6) “SWING” BUTTON
Press “SWING” top turn on or off the swing function.
(7) TEMPERATURE + - AND TIMER ADJUSTMENT BUTTONS
The temperature can be adjusted to between 16 °C and 30 °C.
Increase temperature（+):
1) Allows for adjusting the desired temperature in cooling (COOL) mode.
2）Whenever the（+) button is pressed, the set temperature increases by 1 °C.
Decrease temperature (- ):
1) Allows for adjusting the desired temperature in cooling (COOL) mode.
2）Whenever the ( - ) button is pressed, the set temperature decreases by 1 °C.
The same button allows for setting the TIMER.
(9) TANK OVERFLOW INDICATOR
If the tank is full this led will turn on.
(8) TEMPERATURE AND ERROR DISPLAY
In the event of a malfunction, the LED display shows an error code, which facilitates the solution of the problem. With
the exception of the FL message, full tank, when an error occurs do not attempt to repair the air conditioner, always
take it to an Argoclima Service Center.
Problem
Cause
Solution
FL
Tank full of water.
Empty the tank.
If the problem persists, contact a service centre.
E1
Room temperature sensor failure.
Contact a service centre.
E2
Failure of temperature sensor on the
evaporator.
Contact a service centre.
Il display temperatura ed errori si accende solo nelle modalità COOL. Nelle modalità DRY e FAN non si accende
SAFETY FUNCTIONS

Argo IRO Specifications

General

Type	Monobloc mobile air conditioner
Cord length	1.5 m
Noise level	65 dB
Hose diameter	150 mm
Number of speeds	3
Remotely operated	Yes
Airflow (high speed)	24 m³/h
Cooling capacity (max)	10000 BTU/h
Air conditioner functions	Cooling
Cooling capacity in watts (nominal)	2720 W
Heating capacity in watts (nominal)	- W
Cooling energy efficiency (EER, W/W)	2.6
Display type	LED
Product color	White
AC input voltage	230 V
AC input frequency	50 Hz
Energy efficiency scale	A+++ to D
Energy efficiency class (cooling)	A
Energy efficiency class (heating)	No
Hourly energy consumption (cooling)	1.1 kWh
Hourly energy consumption (heating)	- kWh

Weight and Dimensions

Depth	382 mm
Width	470 mm
Height	770 mm
Weight	28000 g