4 / 4 P/N INT-1000199 (EN) • REV 01 • ISS 27NOV23
LAN addr
Set the keypad bus address. See Axon x700 Control Panel
Installation and Programming Manual for details on the bus
addressing.
Note: Changing keypad address will reset the secure channel
key.
Reset
Use the menu to reset one of the following:
• SC key: Reset the secure channel key stored in the
keypad.
• Logo: Load the default keypad logo.
Note: The keypad logo may be changed using the
Downloader configuration software.
• All: Reset all keypad settings, including LCD brightness,
keypad backlight, buzzer volume, logo and secure channel
key to the default ones. The keypad address is set to Off.
Troubleshooting
Secure communication is only secure between two devices
when both devices agree on proper secure keys. If these are
not aligned, the communication fails, for example, the LCD
keypad shows System Fault, and it cannot be polled by the
control panel. This requires a reset on one or on both devices.
See Axon x700 Control Panel Installation and Programming
Manual for more information.
Specifications
8.7 to 15.1 VDC; 12.0 VDC nom.
Maximum operating current
115 mA at 12.0 VDC
110 mA at 13.7 VDC
25 mA at 12.0 VDC
22 mA at 13.7 VDC
Normally open (NO) contact. Max.
appearing voltage 13.9 VDC
Open collector output (OUT
terminal)
13.7 V max. at 50 mA max.
Wireless operating frequency
Code combinations [1]:
5 digits
10 digits
ACE type (tamper protection)
Unsecure mode: Mifare Unique ID
(Classic 1K/4K, Desfire EV1, EV2,
EV3)
Secure mode: Mifare Desfire EV1,
EV2, EV3
Maximum relative humidity
Security rating (EN62368)
[1] Notes
• When Duress functionality is enabled, 6 digits codes are required
• There are no invalid code combinations
Notification
When printing or adding a customer logo on the ATS1125
keypad or its lens, take care to make use of RoHS compliant
materials and printing processes only.
Regulatory information
Carrier Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, Netherlands
Product warnings
and disclaimers
THESE PRODUCTS ARE INTENDED FOR SALE
TO AND INSTALLATION BY QUALIFIED
PROFESSIONALS. CARRIER FIRE &
SECURITY CANNOT PROVIDE ANY
ASSURANCE THAT ANY PERSON OR ENTITY
BUYING ITS PRODUCTS, INCLUDING ANY
“AUTHORIZED DEALER” OR “AUTHORIZED
RESELLER”, IS PROPERLY TRAINED OR
EXPERIENCED TO CORRECTLY INSTALL FIRE
AND SECURITY RELATED PRODUCTS.
For more information on warranty disclaimers and
product safety information, please check
https://firesecurityproducts.com/policy/product-
warning/ or scan the QR code.
EN 50131-1 System requirements
EN 50131-3 Control and indicating equipment
Security Grade 3, Environmental class II
Tested and certified by Kiwa Nederland B.V.
Carrier Fire & Security hereby declares that this
device is in compliance with the applicable
requirements and provisions of all applicable rules
and regulations, including but not limited to the
Directive 2014/53/EU. For more information see:
www.firesecurityproducts.com
Product may contain substances that are also
Candidate List substances in a concentration
above 0.1% w/w, per the most recently published
Candidate List found at ECHA Web site.
Safe use information can be found at
https://firesecurityproducts.com/en/content/intrusi
on-intro
2012/19/EU (WEEE directive): Products marked
with this symbol cannot be disposed of as
unsorted municipal waste in the European Union.
For proper recycling, return this product to your
local supplier upon the purchase of equivalent
new equipment, or dispose of it at designated
collection points. For more information see:
recyclethis.info
Please consult the following web link to retrieve
the electronic version of the product
documentation.
This link will guide you to the EMEA regional
contact page. On this page you can request your
login to the secured web portal where all manuals
are stored.
https://firesecurityproducts.com/en/contact
Contact information
www.firesecurityproducts.com or www.aritech.com
To Previous Page
Loading...
