Assa Abloy Besam SW300 Installation And Service Manual

Name: Assa Abloy Besam SW300
Brand: Assa Abloy
Rating: 5 (1 reviews)

85 pages

To Next Page

Original instructions

Installation and Service Manual

Swing Door Operator

Besam SW300/SW150

ASSA ABLOY Entrance Systems

Default Chapter3
- Table of Contents3
1 Revision6
2 Instructions for Safe Operation7
3 Important Information8
- Intended Use8
- Safety Precautions8
- Electronic Equipment Reception Interference9
- Environmental Requirements9
4 Technical Specifications10
5 How the Besam SW300/SW150 Works12
- Opening13
- Closing13
- Control Switch13
  - OFF/AUTO/OPEN Switch13
- Functions on the Basic Control Unit CU-30014
- Functions on the Extension Unit EXU-SI16
- Functions on the Extension Unit EXU-SA18
6 Models19
- Single Operator, Surface Mounted19
- Double Operator, Surface Mounted20
7 Part Identification21
8 Arm Systems23
- Pushing Installation with PUSH-Arm23
- Pulling Installation with PULL-Arm24
- Pushing Installation with PULL-Arm25
- Drive Shaft Extension Kits25
9 Options26
- Control Switches26
  - 4-Position Switch PS-4C (Operates the Electric Lock)26
- Sync Cable for Double Doors (Synchronizing of 2 Operators)26
- Coordination Unit (Only for Besam SW300)26
- LED Cable27
- Battery Backup Unit27
- Double Door Kit27
- Closing Time Board Kit (Only for Besam SW300)27
- Fire Kit (Only for Besam SW300)28
- Labels28
10 Pre-Installation29
- General Tips/Safety Concerns29
- Operator/Door Handing29
- Installation Examples30
- Fastening Requirements30
- Tools Required31
- Installation on Double Doors31
11 Mechanical Installation32
- PUSH Arm System36
- PULL Arm System42
- Operator with Sliding PUSH Arm System48
- Besam SW300 Inverse Installation with PUSH Arm System48
- Besam SW300 Inverse Installation with PULL Arm System49
- Installation of Coordination Unit on Fire Door Installations51
12 Electrical Connection54
- Control Units56
- Sensor Cable Inlet62
- Reset and Indication Device for Fire Doors63
13 Start-Up65
- Besam SW300 Spring Pre-Tension65
- Micro Switch (Only for Besam SW300)66
- Adjusting the Door Stop66
- Auto-Learn Automatically Sets Back and Latch Check (Recommended)68
  - Push the LEARN BUTTON (LRN)69
  - Double Doors69
- General Adjustment69
- Connection of Activation Units and Accessories70
14 Changing Group of Parameters72
- Learn with Advanced Setting of "Back- and Latch-Check75
- Revert to Default Values for "Back- and Latch-Check75
15 Classification76
- Entering the Program Mode (Classification)76
- Identify the Current Classification76
- Changing the Classification76
- Classification Table76
16 Cover78
- Fitting and Removing the Cover78
- Cover Piece Kit78
17 Signage79
18 Guide for Installation and Adjustments80
- Complementary Safety Devices Swing Doors80
- Swing Doors Opening and Closing Time80
  - How to Find the Correct Opening and Closing Time80
- Diagrams for Door Weight81
  - Aluminium Frame with Glass81
19 Troubleshooting82
- Error Indication83

Other manuals for Assa Abloy Besam SW300

User Manual14 pages

Questions and Answers:

B
bsmithJul 25, 2025
How to troubleshoot a motor that won't start in Assa Abloy Besam SW300 Door Opening System?
- V
  Victor HodgesJul 26, 2025
  If the motor of your Assa Abloy Door Opening System does not start, you can try the following: * Change the setting of the program selector. * Check that there are no objects in the detection zone if a sensor is fitted. * Check the mains switch and fuse in the building.

Assa Abloy Besam SW300 Specifications

General

Operating Temperature	-20°C to +50°C
Power Supply	230 V AC, 50/60 Hz
Safety Features	Obstacle detection
Humidity	Max 95% RH (non-condensing)
Noise Level	< 60 dB
Compliance	EN 16005
Type	Swing Door Operator
Control System	Microprocessor-controlled