EasyManua.ls Logo

Atag i28C

Atag i28C
82 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
Installation & Servicing instructions ATAG iC-Range
62
4 Zone1parameters
4.0 SetPoint
4.0.0 TDay Roomtemperaturesetpointfordayperiod °C 10‐30 20
4.0.1 TNight Roomtemperaturesetpointfornightperiod °C 10‐30 15
4.0.2 Tsetzone1 FixedTsetforzone1 °C Para4.2.5toPara4.2.6 85HT/50L
T
(usedwithThermoregulationonOFForThermoregulationType1)
4.0.3 ZoneFrostprotection °C 2‐15 5
4.1 S/WChangeover
4.1.0 S/WchangeoverActivation 0‐OFF1‐ON(onlyactivewhenoutsidetemperatureinfluence) 0‐1 0
4.1.1 Threshold °C 0‐30 25
4.1.2 Delaytime timebeforeS/Wchangeoverbecomesactive min 0‐300 300
4.2 Zone1settings
4.2.0 Zone1systemtype 0=lowtemperaturesystem1=hightemperaturesystem 0‐1 1
4.2.1. Zone1thermoregulationtype 0=Fixedflowtemperature 0‐4 0
1=donotuse
2=Roomtemperatureonly
3=OutdoorTemperatureonly(On/OffThermostatworks)
4=Room+Outdoortemperature(e‐busthermostatneeded)
4.2.2 SlopeHeatingLine 0,2‐1forLowtemperatureinstallation
s
0,2‐3,5 0,6LT/1,5H
T
1‐3,5forhightemperatureinstallations
4.2.3 Offsetheatingline
offsetheatinglineadjustableper°C
°C ‐7‐+7LT‐14‐+14H
T
0
Lowtemperaturesystem‐7‐+7
Hightemperaturesystem‐14‐+14
4.2.4 Roominfluenceproportional HeatingcurveproportionalRoominfluence 0‐20 2LT‐10H
T
4.2.5 MaximumTemperature Zone1MaximumFlowTemperature °C 20‐50LT20‐85H
T
50‐LT80‐H
T
4.2.6 MinimumTemperature Zone1minimumFlowTemperature °C 20‐50LT20‐85H
T
50‐LT80‐H
T
4.2.8 Quicknightsetback donotchange OFF‐ON OFF
4.2.9 HeatRequestMode donotchange 0‐2 0
4.3 Zone1Diagnostics
4.3.4 HeatRequestZone1 isthereaHeatdemandfromthiszone0‐OFF1‐ON 0‐1
4.7 Zone1Regulationparameters
4.7.0 HeatingType 0=FloorHeating 0‐5 1
1=Radiators
2=Floorheating(main)+Radiators
3=Radiators(main)+Floorheating
4=Convection
5=Airheating
4.7.1 Roominfluence 0=OFF 0‐3 0
1=Less
2=Medium
3=Good
4.7.2 Buidinginsulationlevel 0=Poor 0‐2 0
1=Average
2=Good
4.7.3 Buidingsize 0=Small 0‐2 0
1=Average
2=Large
4.7.4 ClimateZone Settingasabasefortheheatlinecalculation ‐60‐+50 ‐10
4.7.5 Autoslopeadaptation 0=Off1‐On 0‐1 0
4.7.6 Pre‐heatFunction 0=Off1‐On 0‐1 1
5 SettingsZone2 Seezone1chapter4
6 SettingsZone3 Seezone1chapter4
8 ServiceParameters
8.0 Boilerstatistics‐1
8.0.0 divertervalve numberofdivertervalvecycles times xx
8.0.1 Pump numberofrunninghourspump h xx
8.0.3 Boilerlifetime numberofhourssince1stboilerpowerup. h xx
8.1 Boilerstatistics‐2
8.1.0 BurneronCH numberofhoursburneractiveforCH h xx
8.1.1 BurneronDHW numberofhoursburneractiveforDHW h xx
8.1.3 Ignition numberofignitioncycles times xx
8.2 Boiler
8.2.1 Fanstatus Fan:0=OFF1=ON
8.2.2 Fanspeed Numberofrevolutions Rpm
8.2.4 Divertervalveposition positionofthedivertervalve0=DHW1=CH
8.2.5 DHWflowrate l/min
8.2.7 pumpmodulation %
8.2.8 gaspower actualboilerpowerbasedonfanrevolutions kW
8.2.9 systempressure bar
8.3 Boilertemperatures
8.3.0 CHT‐Set calculatedtargetflowtemperature °C
8.3.1 CHflowtemperature °C
8.3.2 CHReturntemperature °C
8.3.3 DHWTemperature °C
8.3.4 fluegastemperature onlyiffluegassensorisconnected °C
8.3.5 Outsidetemperature onlyifoutsidesensorisconnectedorconnectedtotheinternet °C
8.4 Storage
8.4.0 n.a.
8.4.2 n.a.
8.5 Service
8.5.0 Monthstonextmaitenance MonthstogobeforenextMaintenancewarningcomesup 0‐60 12
8.5.1 Maintenancewarningactive switchonorofthemaintenancewarning0=OFF1=ON 0‐1 0
8.5.2 Maintenancewarningreset Resetthemaintenancewarninginthedisplayandthetimer 0‐1
8.6 ErrorHistor
y
8.6.0 Errorhistor
y
overviewofthelast10errorsoccured
8.6.1 ResetErrorlis
t
OK=YesESC=No
8.7 FreeParameter
8.7.5 IonizationCurrent
8.7.6 SafetyFlameSensor burnerstatusoftheboiler0=OFF1=ON
8.7.7 CHFlowswitchState 0=OFF1=ON

Table of Contents

Other manuals for Atag i28C

Related product manuals