Need help?Do you have a question about the Atlas 210x and is the answer not in the manual?
General| Brand | Atlas |
|---|---|
| Model | 210x |
| Category | Transceiver |
| Language | English |
Details the Atlas 210x/215x transceiver's design, bands, and company background.
Details frequency bands, VFO control, readout, and external frequency options.
Explains solid-state design, modularity, and plug-in capabilities.
Covers power requirements, front panel controls, physical finish, weight, and dimensions.
Details receiver front-end, sensitivity, selectivity, and AGC characteristics.
Covers selectivity, audio response, and speaker integration.
Explains calibrator function and S-meter operation.
Details broadband design, filters, ALC, SWR protection, and frequency control.
Covers power ratings, emission types, and performance metrics like distortion.
Details AC input power and regulated DC output for the 220-CS console.
Details AC input power and regulated DC output for the 200-PS supply.
Describes the GC1400 battery pack, its features, and availability.
Intro to installations, DC power sources, and automotive system precautions.
Details on 220-CS console, portable battery pack, and various cables.
Details the 200-PS supply and transmission line impedance matching.
Covers SWR protection, measurement, and ammeter use.
Details microphone types, CW key jack, and connections.
Explains VOX setup and remote CW transmit switch.
Describes sockets for accessories and linear amplifier connection.
Details DMK components and steps for mobile mounting.
Details MBK components and mounting options.
Covers DC power cable routing, battery connection, and safety.
Covers circuit breaker installation and alternative DC wiring.
Requirements for fixed stations and mobile antenna use.
Covers impedance matching and automotive noise suppression.
Discusses fixed station antennas and antenna tuner functions.
Overview of operating controls, indicators, and connections.
Explains power on/off functions and the function switch modes.
Explains AF Gain, RF Gain, and band selector operation.
Explains Dial Set, Carrier Balance, S-meter zeroing, and calibrator use.
Guidance on proper SSB tuning and voice transmission procedure.
Adjusting modulation, ALC, and CW operation details.
Importance of proper heat sink ventilation during operation.
Overview of circuit design and receiver front-end.
Details receiver sensitivity, selectivity, and oscillator switching.
Explains broadband design and alignment/troubleshooting.
Notes and guidelines for taking voltage measurements.
Charts detailing signal ranges and local oscillator frequencies.
Details the PC-100C circuit, including components and function.
Details the PC-200C circuit, including components and function.
Provides voltage chart and schematic for PC-100C board.
Details the PC-300C circuit, including components and function.
Provides voltage chart and schematic for PC-200C board.
Provides voltage chart and schematic for PC-300C board.
Details the PC-500D/520A circuit, including components and function.
Provides voltage chart and schematic for PC-500D/520A.
Details the PC-400C VFO circuit and tuning components.
Provides schematics for the PC-400C VFO and tuning sections.
Details the PC-600 circuit for carrier generation and buffering.
Provides voltage chart and schematic for PC-600 board.
Details receiver input tuning components for PC-800C/1200.
Provides schematics for receiver input tuning on PC-800C/1200.
Details the PC-820 crystal calibrator circuit, voltage, and schematic.
Details transmitter input tuning components for PC-900C.
Provides schematic for PC-900C transmitter input tuning.
Details the PC-1010/1020 low pass filter components and function.
Provides schematic for PC-1010/1020 low pass filters.
Details the PC-1100A SWR bridge and antenna relay circuit.
Details the PC-120 noise blanker accessory.
Provides the schematic diagram for the PC-120 noise blanker.
Details the Model 10x crystal oscillator, its function, and ranges.
Covers installation steps and crystal specifications for the 10x.
Explains how to calculate crystal frequencies for LSB and USB.
Details the MT-1 transformer for impedance matching.
Details the VX-5 VOX accessory for the console.
Describes the DD-6B digital dial and frequency counter capability.
Details the warranty period for components and semiconductors.
Covers warranty transfer and classifies it under Magnuson-Moss Act.
To Next Page
