Directions of Assembly and
Operation of “In-Line” Instant
Water Heater
An Inatant appliance is novel device designed to
supply hot water instantaneously upon demand
while conserving electricity, water and energy.
The In-Line is the most advanced heater in the
Instant family and as such can be installed
anywere, and serve any purpose. When the flow
switch turns on the electrical current, the heating
element heats only the amount of water
economically needed for use.
InLine - 3.0 1.0;2.0 or 3.0kW 3.0 3.3 3.6 2.5mm
2
16amps
InLine - 3.5 1.5;2.0 or 3.5kW 3.2 3.5 3.8 2.5/4mm
2
20amps
InLine - 5.0 2.0;3.0 or 5.0kW 5.0 5.5 6.0 4/6mm
2
25amps
InLine - 5.5 2.5;3.0 or 5.5kW 5.5 6.0 6.6 4/6mm
2
25-32amps
InLine - 7.0 3.0;4.0 or 7.0kW 7.0 7.7 8.3 6/10mm
2
40amps
InLine - 8.0 4.0;4.0 or 8.0kW 7.3 8.0 8.7 6/10mm
2
40amps
InLine - 9.5 4.5;5.0 or 9.5kW 8.7 9.5 10.3 10mm
2
45amps
Model Heat Setting
kW loading
Recommended
cable size
Recommended
fuse rating
220V 230V 240V
• Operating water pressure 0.3-7 BAR (5-100 psi) • Water pressure operated flow switch
• Standard 1/2"fl compression inlet connection • Top-left and right cable entry • Bottom-left water entry
UNIT DIMENSIONS: HEIGHT 185mm WIDTH 300mm DEPTH 110mm
Table I recommended cable & fuse
3.3 Device with an output 380V - 400V up to 12kW (three phase)
1. A separate electrical line is needed as device of this output.
2. The device must be connected to a separate multi polar circuit breaker of 3 x 20A.
3. The recommanded electrical cable for feeding the device is 5 x 4mm
2
.
4. I single - phas network, the device will be connected to a single polar circuit breaker of 60A and
cable (3 x 10mm
2
) or (3 x AWG -6).
For one phase
or 2 x 127V(2~)
are
short circuited
together
R
8
L1
L2
L3
N
E
2 3
4
5
6
7
1. 3 - pole switch
2. Terminal block
3. Thermostat with reset
4. Read sensor
5. Switches with lights
6. Relay
7. Heating elements
8. Thermostat
ELECTRICAL
WATER HEATER
ELECTRICAL
WATER HEATER
INCORRECT INSTALLATIONCORRECT INSTALLATION
INSTANT WATER HEATER
.
H
I
D
D
E
N
I
N
S
T
A
L
L
A
T
I
O
N
Directions of Assembly and
Operation of “In-Line” Instant
Water Heater
An Inatant appliance is novel device designed to
supply hot water instantaneously upon demand
while conserving electricity, water and energy.
The In-Line is the most advanced heater in the
Instant family and as such can be installed
anywere, and serve any purpose. When the flow
switch turns on the electrical current, the heating
element heats only the amount of water
economically needed for use.
P.N. 166015B?
To Next Page
Need help?
General
