Audio Technica 60th ANNIVERSARY AT-LP2022 User Manual

Contents
Preparation
Use the included gloves to avoid fingerprints on the turntable.
1
With the turntable turned off, set the platter.
Motor pulley
2
Attach the drive belt to the motor pulley.
3
Level the turntable.
4
Insert the headshell into the tonearm, and remove the
cartridge’s protector.
Protector
5
Attach the counterweight to the back of the tonearm, and
slowly turn it counterclockwise (to the left).
6
Unlatch the clamp.
Clamp
7
Turn the counterweight to adjust the tonearm’s balance so that
the tonearm is level when you release the headshell.
Tonearm
8
Set the tracking force gauge ring to the “0” position.
After that, turn the counterweight and the tracking force gauge
ring together counterclockwise (to the left) to the “2” position.
0
2
Tracking force gauge ring
9
Set the anti-skate control dial to “2”, the same value as the
tracking force value.
Anti-skate control dial
Dust cover hinges Headshell with VM stereo cartridge
Counterweight 45 RPM adapter AC adapter RCA audio cable
Hexagonal wrench
(For tonearm height adjustment)
Gloves
Turntable body
Dust cover
Quick Start Guide
Belt-Drive Turntable
Guide de démarrage rapide
Tourne-disque à entraînement par courroie
Kurzanleitung
Riemenbetriebener Plattenspieler
Guida rapida
Giradischi
Guía de inicio rápido
Giradiscos de tracción por correa
Guia de início rápido
Toca-discos acionado por correia
Краткое руководство по установке
Проигрыватель с ременным приводом
快速启动指南
皮带传动唱盘机
快速入門指南
皮帶驅動式黑膠唱機
간편 사용 설명서
벨트 드라이브 턴테이블
Quick Start Guide
AT-LP2022
Back side with hexagonal nut
Drive belt
Platter (with drive belt)
(Remove the protective sheet before use.)
Replacement stylus
(AT-VMN95SH CL)
User Manual (Online Manual)
https://www.audio-technica.co.jp/document/AT-LP2022/
Default.html

Audio Technica 60th ANNIVERSARY AT-LP2022 Specifications

General

Drive Method	Belt-drive
Type	Manual
Motor	DC motor
Speeds	33-1/3 RPM, 45 RPM
Cartridge	AT-VM95E
USB ADC	No
Tonearm	Carbon-fiber
Replacement Stylus	AT-VMN95E
Outputs	RCA output terminals
Power Supply	100-240V AC, 50/60 Hz
Accessories Included	AC adapter, 45 rpm adapter, dust cover, RCA cable

Summary

Quick Start Guide - Preparation

Set the Platter

Position the platter onto the turntable spindle.

Attach the Drive Belt

Connect the drive belt to the motor pulley.

Level the Turntable

Ensure the turntable is properly leveled.

Install Headshell and Remove Protector

Insert the headshell into the tonearm and remove the cartridge protector.

Attach and Adjust Counterweight

Attach the counterweight to the tonearm and adjust for balance.

Unlatch Tonearm Clamp

Release the clamp securing the tonearm.

Set Tracking Force and Anti-Skate

Set tracking force to '2' and anti-skate control to '2'.

Turntable Connection

Connect to Amplifier

Connect the turntable to a phono equalizer or amplifier.

Power On

Turn on the turntable after all connections are made.

Playing a Record

Remove Cartridge Protector

Remove the protector from the stylus before playing.

Select Speed and Start Playback

Turn on the turntable and select the record speed.

Position Tonearm

Raise and position the tonearm over the desired groove.

Lower Tonearm

Use the lift control lever to lower the tonearm onto the record.

Stopping Playback

Lower Volume and Stop

Lower connected device volume and set control knob to 'STOP'.

Return and Raise Tonearm

Return tonearm to rest and raise it using the lift control.

Turn Off Turntable

Turn the turntable off using the power switch.

Replacing the Stylus

Release Headshell

Release the headshell from the tonearm.

Remove Old Stylus

Pull the old stylus in the direction of the arrow.

Mount New Stylus

Mount the new replacement stylus to the cartridge.

Mount Headshell

Mount the headshell back onto the tonearm.

Adjust Balance and Tracking Force

Adjust tonearm balance and tracking force.

Cleaning

General Cleaning Instructions

Clean the turntable and accessories as needed.

Stylus and Record Care

Refer to website for stylus and cartridge care accessories.