AUTOLIFT BBW 1350 - User Manual

Questions and Answers

M
Mrs. Julie McfarlandAug 14, 2025
How to fix warning light not coming on in AUTOLIFT Lifting Systems?
- A
  Arthur WeberAug 14, 2025
  If the warning light in the cab of your AUTOLIFT Lifting Systems isn't turning on, several issues could be the cause. First, check if the power switch is turned to the OFF position and switch it to ON. If that doesn't work, examine the hydraulic power unit fuse and reset it if it's open. Also, inspect the main power fuse and replace it if it's blown. The cab warning light itself might be broken, so consider replacing it. Lastly, check the electronic control unit fuse and replace it if necessary.
M
Monica WhiteAug 17, 2025
What to do if AUTOLIFT BBW 1350 platform does not rise?
- T
  Theresa SullivanAug 17, 2025
  If your AUTOLIFT Lifting Systems platform isn't rising, several factors could be at play. Ensure the lowering valve screw is properly tightened by closing the lowering valve. If the lowering valve is broken, replace it. A broken electro-pump remote switch or the electro-pump itself could also be the issue, requiring replacement. Check the push-button panel and the electronic control unit, replacing them if broken. Insufficient battery charge can prevent the platform from rising, so ensure the battery is charged. A dirty earth connection can also cause this problem, so clean it. If the hydraulic power unit is broken, it will need to be replaced. Finally, if the max speed control is set too low, calibrate the speed to an appropriate level.
Z
zshepherdAug 21, 2025
Why AUTOLIFT BBW 1350 platform does not open?
- S
  Susan BarnesAug 21, 2025
  If the platform on your AUTOLIFT Lifting Systems is not opening, first ensure the push-button panel is correctly connected. If there is intermittent power on the solenoid line, restore continuous power. If the lowering valve solenoid or the lowering valve is broken, replace them. For SKY and BBW models, check if the hinges are locked and apply oil and grease. If the push-button panel or the electrical control unit is broken, they should be replaced.
G
Gina EllisAug 25, 2025
What to do if AUTOLIFT Lifting Systems platform does not descend?
- K
  karenperezAug 25, 2025
  If the platform on your AUTOLIFT Lifting Systems doesn't descend, start by checking the push-button panel connection and ensure it's correctly connected. Restore continuous power to the solenoid line if there's intermittent power. If the lowering valve solenoid or the lowering valve is broken, replace them.
C
carmenarmstrongAug 28, 2025
How to troubleshoot AUTOLIFT Lifting Systems platform not closing?
- D
  Daniel WatsonAug 28, 2025
  If the platform of your AUTOLIFT Lifting Systems is not closing, make sure the lowering valve screw is tightened by closing the lowering valve. Ensure the pressure switch is correctly calibrated. If the lowering valve, electro-pump remote switch, electro-pump, push-button panel, or electronic control unit are broken, replace them.
H
harrellandrewAug 31, 2025
Why AUTOLIFT BBW 1350 Lifting Systems platform does not stop when opening?
- K
  Kathleen LivingstonAug 31, 2025
  If the platform on your AUTOLIFT Lifting Systems isn't stopping at the loading surface when opening, check the micro switch M1 connections and ensure the control wire is correctly connected. Restore continuous power to the micro M1 line if the power is intermittent. If the micro M1 cam is not adjusted correctly, adjust it. If the micro M1 is broken, replace it.
B
Barbara ArmstrongSep 3, 2025
Why AUTOLIFT Lifting Systems platform does not stop when rising?
- M
  Morgan AguirreSep 3, 2025
  If the platform on your AUTOLIFT Lifting Systems is not stopping at the loading surface when rising, check that the micro M1 is correctly connected. If there's intermittent power on the micro M1 line, restore continuous power. If the micro M1 cam isn't adjusted correctly, adjust it. If the micro M1 is broken, replace it.
J
Julia BrooksSep 6, 2025
How to control descent of AUTOLIFT Lifting Systems platform?
- M
  Melinda HowellSep 7, 2025
  If the platform descent on your AUTOLIFT Lifting Systems is not properly controlled, ensure the lowering valve screw is tightened by closing the lowering valve. If the lowering valve is broken, replace it.
K
kenneth22Sep 10, 2025
What to do if AUTOLIFT BBW 1350 Lifting Systems platform does not close completely?
- D
  daniellehesterSep 10, 2025
  If the platform on your AUTOLIFT Lifting Systems does not close completely, ensure that the pressure switch is correctly calibrated and recalibrate the maximum speed.