K-90
LE365S-41
Functions
ON time
Pulse width
(1 to 59sec., 1 to 60min.)
Weekly setting 1 of Program1
Weekly setting 2 of Program1
Yearly setting 1 of Program1
①②③④⑤⑥
Output operation
ON Time ON width OFF Time
OFF width
•Set range for ON/OFF time width : 1min. to 12 hour 59min.
• One record in 3 steps(ON day/ON time, OFF day/OFF time,
ON time width/OFF time width)
● Weekly pulse mode
Output turns ON at ON time for a specifi ed pulse width.
(Pulse width : 1 to 59sec., 1 to 60min.)
• One record in two steps(ON day/ON time, pulse width)
● Yearly ON/OFF mode
Output turns ON at ON time on START date and turns OFF
at OFF time on STOP date.
• One Record in three Steps(START/STOP date, ON/OFF
time)
● Yearly pulse mode
Output turns ON at ON time on START date and turns OFF at
OFF time on STOP time for a specifi ed pulse width repeatedly.
• One record in three steps(START/STOP date, ON time,
Pulse width)
Program operation
●
①
to
②
: Operated by weekly setting 1 of Program 1.
●
②
to
③
: Operated by weekly setting 2 of Program 1.
●
④
to
⑤
: Operated by weekly setting 1 of Program 1.
●
⑤
to
⑥
: Operated by yearly setting 1 of Program 1.
(During weekly program operation at 12:00 AM on START
date, the weekly program operation stops, and it changes
to yearly program operation mode. The yearly program
operation stops at 12:00 AM on the next day of STOP
date.)
Display and change of next mode
● The day of next mode in Program is displayed on the day
indicator, and the time of next mode is displayed on the
lower row of screen.
● In ON/OFF operation mode, set ON time and OFF time to
next mode. In Pulse operation mode, set Pulse ON time
to next mode.
Power restore mode
In setting group 2 - LEVEL2 (" " turns ON
,
" " or "
" fl ashes), select Auto(" ") or Normal(" ") by or
key and press
SET
key to set.
●Auto ("
") power restore mode
Output operates according to program when power turns
ON again after power failure.
●Normal("
") power restore mode
When power turns ON again after power failure, output
is kept OFF and "
" fl ashes on the lower row of screen
and power restore input (press
SET
key over 3 sec.
in RUN mode) is applied, "
" turns OFF and output
operates according to program.
Season switching mode
This feature uses for setting seasonal weekly operation
mode. To operate this mode, save starting month and date,
ending month and date of each season which displays S1,
S2, S3, S4 then set day and time of each season in weekly
program setting. It is also able to operate only in summer
and winter season. (S1: set summer season, S2: set winter
season, S3/S4: do not set)
In setting group 2-Level 2("
" turns ON, " " fl ashes.),
select ON("
") by or key and press
SET
key to save.
*
Note:When the season switching mode changed from
" " to " "or vice versa, previous set programs are
deleted.
● ON("
") mode
Weekly program is switched automatically by season switching.
• Period setting per season
①
Press
SET
key in period setting per season mode of setting
group 2.("
"
fl ashes
, season with preset period
turns ON
and "START" and "STOP" turn ON.)
②
Advance to the fl ashing position of season selectionamong
S1, S2, S3, S4 by or key and press
SET
key.
③
After set START month, date per season and press
SET
key.
④
SET
key is pressed after set STOP month, date per season,
it is advanced to LEVEL1 of period setting per season. Ad
d
or adjust the period setting by
SET
key.
● It is disable to use when it is OFF("
").
● If season terms are overlapped, these are prioritized in
S4>S3>S2>S1 order.
To Next Page
Loading...
