Pressure Static
0.1 kPa 0.1 kPa 1 kPa 0.1 kPa
MPa - - 0.001 - 0.001 - - -
kPa 0.1 - 0.1 - 1 - - 0.1
2
0.001 - 0.001 - 0.01 - - 0.001
bar 0.001 - 0.001 - 0.01 - - 0.001
- 0.01 - 0.01 - 0.1 - 0.02
- 0.4 - 0.8
- 0.02 - 0.03
mmH
2
O
0.1 - - 0.1
01) Multiply display value by 100.
Model
PSAN-
PSAN-
PSAN-
Pneumatic type model: Gauge pressure
Fluid type model: Gauge pressure
01)
or sealed gauge pressure
02)
Pressure Negative Static Compound
0.1 kPa 0.1 kPa 1 kPa 0.1 kPa
0.0 to -101.3
kPa
0.0 to 100.0
kPa
0 to 1,000 kPa
-101.3 to 100.0
kPa
5.0 to -101.3
kPa
-5.0 to 110.0
kPa
-101.3 to 1,100 kPa
-101.3 to 110.0
kPa
7 Segment LED, 4 ½ digit
-10 to 0 ℃: ≤ ±1% F.S., 0 to 50 ℃: ≤ ±0.5% F.S.
Rated pressure
×2
Rated
pressure ×2
• Pneumatic type:
Rated pressure ×1.5
• Fluid type: Rated
pressure ×2
Rated pressure
×2
01) Only for static pressure, rated pressure range 100.0 kPa model
02) The unit is sealed structure. It is based on atmospheric pressure 101.3 kPa.
medium
Connector type Cable type / connector type
Cable Ø 4 mm, 5-core, 2 m
Connector type: Ø 4 mm, 5-core, 2 m
Cable type: Ø 4 mm, 5-core, 3 m
AWG24 (0.08 mm, 40-core), insulator diameter: Ø 1 mm
Material
Front case: PC
Back case: (back port) PC /
(bottom port) PBT+GF15%
Pressure port: Brass-nickel plated
Front case: PC
Back case: PA6
Pressure port: SUS304/SUS316L
Protection
structure
Connector type: IP40 (IEC standard)
Connector type: IP40 (IEC standard)
Cable type: IP65 (IEC standard)
ᜢ ᜫ
Back port: ≈ 80 g (≈ 165 g)
Bottom port: ≈ 85 g (≈ 170 g)
Connector type: ≈ 88 g (≈ 173 g)
Cable type: ≈ 90 g (≈ 167 g)
12 - 24 VDCᜡ (ripple P-P: ≤ 10%)
90 to 110% of rated voltage
≤ 50 mA
01)
NPN open collector output / PNP open collector output model
Load voltage ≤ 30 VDCᜡ
Load current ≤ 100 mA
Residual voltage NPN: ≤ 1 VDCᜡ, PNP: ≤ 2 VDCᜡ
Hysteresis According to output operation mode
02)
Repeat error ±0.2% F.S. ±min display interval
Response time 2.5, 5, 100, 500, 1000 ms
Protection circuit Output short over-current protection circuit
Insulation resistance ≥ 50 MΩ (500 VDCᜡ megger)
Between the charging part and the case: 1,000 VACᜠ 50 / 60 Hz for 1 min
Vibration
1.5 mm amplitude at frequency of 10 to 55Hz in each X, Y, Z direction
for 2 hours
-10 to 50 ℃, Storage: -20 to 60 ℃ (no freezing or condensation)
Ambient humidity 30 to 80%RH, Storage: 30 to 80%RH (no freezing or condensation)
01) Current output: ≤ 75 mA
02) Refer to 'Output operation mode'. ±1digit error may occur due to pressure unit operation.
Output impedance 1 kΩ -
Linearity ≤ ±1% F.S ≤ ±1% F.S
Zero-point ≤ 1 VDCᜡ ±2% F.S. ≤ DC 4 mA ±2% F.S.
Span ≤ 4 VDCᜡ ±2% F.S. ≤ DC 16 mA ±2% F.S.
Resolution 1/1000 or 1/2000 (dierent by pressure type and display unit)
Response time 50 ms 70 ms
[M] for over 3 sec
[M] for over 3 sec
[M]
[M]
[▼]+[▲] for over 1
sec after remove the
external pressure
adjustment
Displays 0.0 and
returns automatically
[▲] for over 3 sec
[M]
Reset or set: [▼]+[▲]
for over 1 sec
01) Max. / Min. pressure value is available to check by monitoring.
[Option external input model] Auto shift judgment level checking / setting is available when P-9 External input
terminal is set as SHFT. (no input displays 0)
• Some parameter are activated / deactivated depending on other parameters. Refer to
the description.
• The setting item name and setting value are cross-displayed on the display part.
• It returns to RUN mode when there is no additional key input for 60 sec in each
parameter group.
• Guaranteed write life: 100,000 times
• [M] key: Saves setting value and moves to next parameter
[▼], [▲
] key: Selects setting value
Parameter Default
P-1 Display unit UNIT
KPA
[Negative / Compound pressure model]
kPa, KGC: kgf/cm
2
, bar, psi, mmHg, inHg, H2O: mmH
2
O
MPA
[Static pressure model]
MPa, kPa, KGC: kgf/cm
2
, bar, psi
P-2
OUT
operation
mode
OUtM OFF
HYS.M: Hysteresis
WIN: Window comparison output
HY-W: Hysteresis-Window comparison output
AUTO: Auto sensitivity setting
F.OUT: Forced output control
P-3 Output type NoNC 1O2O
OUT1 OUT2
1O2O Normally open Normally open
1O2C Normally closed Normally open
1C2O Normally closed Normally open
1C2C Normally closed Normally closed
P-4
Response
time
SPD @5 2.5, 5.0, 100, 500, 1,000 ms
P-5
Voltage low
limit scale
A-1V )0
[Option voltage output model]
Min. rated pressure ≤ Low limit scale ≤ 90% of rated
pressure
P-6
Voltage high
limit scale
A-5V 10)0
[Option voltage output model]
Low limit scale setting value + 10% of rated pressure
≤ High limit scale ≤ Max. rated pressure
P-7
Current low
limit scale
A-04 )0
[Option current output model]
Min. rated pressure ≤ Low limit scale ≤ 90% of rated
pressure
P-8
Current high
limit scale
A-20 10)0
[Option current output model]
Low limit scale setting value +10% of rated pressure ≤
High limit scale ≤ Max. rated pressure
P-9
External
input
terminal
D-IN HOLD
[Option external input model]
HOLD: Hold
SHFT: Auto shift
P-10
Auto shift
output
01)
ShOT OUT1
[Option external input model]
OUT1, OUT2, ALL
P-11 Lock LOCK LOC1
LOC1: Parameter, preset, zero-point adjustment setting
lock / Monitoring value reset lock
LOC2: Parameter lock (available to check setting value)
OFF
01) Condition: P-9. External input terminal SHFT setting
To Next Page
Loading...
