EasyManua.ls Logo

Banner QS30LLPQ User Manual

Banner QS30LLPQ
12 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
Polarized Retroreflective Laser Sensors
Features
Visible class 1 laser with small, effective beam size
Excellent optical performance throughout sensing range, even close up
Easy push-button SET options: Maximum Excess Gain or Low-Contrast
SET, depending on model, plus Manual Adjust
Easy-to-read operating status indicators, with 8-segment bargraph display
Bipolar discrete outputs, PNP and NPN
Selectable 30 millisecond OFF-delay
Models available with 2 m or 9 m (6.5' or 30') cable or integral quick-discon-
nect
Tough ABS housing rated IEC IP67; NEMA 6
Compact housing, mounting versatility – popular 30 mm threaded nose or
side-mount
Excellent for applications where high sensing power and small beam size are important. Operates over sensing ranges typically accom-
plished only by conventional opposed-mode photoelectrics; uses a special filter to polarize the emitted light, filtering out unwanted reflec-
tions from shiny objects.
Models
Model Range and Use Spot Size at Fo-
cus
Cable* Supply Output Type
QS30LLP
0.2 to 18 m (0.67 ft to 60 ft)
Maximum Excess Gain SET
for Long-Range Applications
Approx. 4 mm at
10 m (0.16 in at 33
ft)
2 m (6.5 ft) 5-wire Ca-
ble
10 to 30V dc
Bipolar NPN /
PNP
QS30LLPQ
Integral 5-pin Euro-
style QD
QS30LLPC
0.2 to 18 m (0.67 ft to 60 ft)
Low-Contrast SET for Small
Object Detection
2 m (6.5 ft) 5-wire Ca-
ble
QS30LLPCQ
Integral 5-pin Euro-
style QD
* 9 m (30 ft) cables are available by adding suffix “W/30” to the model number of any cabled sensor (e.g., QS30LLP W/30). A model with
a QD connector requires a mating cable (see Quick-Disconnect Cables on page 10).
WARNING: Not To Be Used for Personnel Protection
Never use this product as a sensing device for personnel protection. Doing so could lead to serious
injury or death. This product does NOT include the self-checking redundant circuitry necessary to allow its
use in personnel safety applications. A sensor failure or malfunction can cause either an energized or de-
energized sensor output condition.
WORLD-BEAM QS30 LLP and LLPC
P/N 112355 Rev. C 12/18/2013
0 112355 5
Question and Answer IconNeed help?

Do you have a question about the Banner QS30LLPQ and is the answer not in the manual?

Banner QS30LLPQ Specifications

General IconGeneral
Sensing Mode (General)Diffuse
Output TypePNP
Supply Voltage10-30 V DC
Environmental RatingIP67
Input/OutputDiscrete
QD Length (m)2 m
Lens MaterialAcrylic
Discrete (Output Type)PNP
Light SourceLED

Summary

Sensor Configuration Overview

Modes and Controls

Describes SET, SETUP, Manual Adjust modes, and the function of push buttons for configuration.

Remote Configuration and Control

Maximum Excess Gain SET

Details the procedure for setting maximum excess gain for Model QS30LLP.

Manual Adjustment - Max Excess Gain

Describes how to adjust the switchpoint up or down using push buttons.

Low-Contrast SET Configuration

Low-Contrast SET Procedure

Details setting a switchpoint at 35% below the signal from the retroreflector for Model QS30LLPC.

Manual Adjustment - Low-Contrast

Describes adjusting switchpoint up or down by 5% increments using push buttons.

SETUP Mode Operations

Installation and Performance Guidance

Technical Specifications

Laser Classification and Safety

Safe Laser Use Guidelines

Provides essential precautions for safe laser operation as a Class 1 laser product.

Connection and Accessory Information

Related product manuals