Bard WH361 - Figure 15 Fan Blade Setting; Fan Blade Setting Dimensions; Removal of Fan Shroud; Refrigerant Charge

Manual 2100-193
Page 21
FAN BLADE SETTING DIMENSIONS
Shown in the drawing below are the correct fan blade
setting dimensions for proper air delivery across the
outdoor coil.
Any service work requiring removal or adjustment in
the fan and/or motor area will require that the
dimensions below be checked and blade adjusted in or
out on the motor shaft accordingly.
e Settin
REMOVAL OF FAN SHROUD
1. Disconnect all power to unit.
2. Remove the screws holding both grilles, one on each
side of unit, and remove grilles.
3. Remove screws holding fan shroud to condenser and
bottom – nine (9) screws.
4. Unwire condenser fan motor.
5. Slide complete motor, fan blade, and shroud
assembly out the left side of the unit.
6. Service motor/fan as needed.
7. Reverse steps to reinstall.
REFRIGERANT CHARGE
The correct system R-22 charge is shown on the unit
rating plate. Optimum unit performance will occur with
a refrigerant charge resulting in a suction line
temperature (6 inches from compressor) as shown in
Table 9.
The suction line temperatures in Table 9 are based upon
80ºF dry bulb/67ºF wet bulb (50 percent R.H.)
temperature and rated airflow across the evaporator
during cooling cycle.
TABLE 10
INDOOR BLOWER PERFORMANCE
CFM AT 230 VOLTS
.P.S.E
HnI
2
O
163HW,103HW
deepSwoLdeepShgiH
/lioCyrDlioCteW/lioCyrDlioCteW
0./059539/593,1513,1
1./039519/043,1072,1
2./019588/582,1091,1
3./558038/502,1001,1
4./008557/011,1000,1
5./------/500,1078
6./------/------
TABLE 12
MAXIMUM ESP OF OPERATION
ELECTRIC HEAT ONLY
ledoM
teltuOtnorFteltuOpoT
woL
deepS
hgiH
deepS
woL
deepS
hgiH
deepS
103HW
163HW
00A
50A
01A
51A
05.
04.
53.
53.
05.
05.
04.
04.
05.
04.
52.
AN
05.
05.
04.
AN
103HW
163HW
00B
60B
90B
51B
05.
04.
53.
53.
05.
05.
54.
54.
05.
AN
03.
AN
05.
AN
04.
AN
103HW
163HW
00C
60C
90C
51C
05.
05.
03.
03.
05.
05.
04.
04.
05.
AN
53.
AN
05.
AN
54.
AN
Values shown are for units equipped with
standard 1" throwaway filter or 1" washable
filter. Derate ESP by .15 for 2" pleated filter.
FIGURE 15
FAN BLADE SETTING
TABLE 8
FAN BLADE DIMENSION
ledoMAnoisnemiD
103HW
163HW
52.1
TABLE 9
SUCTION LINE TEMPERATURES
ledoM
detaR
wolfriA
DOF59
erutarepmeT
DOF28
erutarepmeT
103HW001,185-6556-36
163HW001,115-9486-66
TABLE 11
CFM and ESP
QRated CFM and ESP on high speed tap
ledoM
j
detaR
MFC
j
detaR
PSE
dednemmoceR
egnaRwolfriA
103HW
163HW
000,1
001,1
03.
03.
003,1-039
053,1-039