Barko 6025 - Electrical System Maintenance; Electrical System Description; Electrical System Inspection; Battery Disconnect Switch

page 30page 30
page 30page 30
page 30
240 Harvester Feller/
Buncher
ELECTRICAL SYSTEM DESCRIPTIONELECTRICAL SYSTEM DESCRIPTION
ELECTRICAL SYSTEM DESCRIPTIONELECTRICAL SYSTEM DESCRIPTION
ELECTRICAL SYSTEM DESCRIPTION
This machine has 24 Volt electrical system with alternator, negative ground, and 24 Volt battery.This machine has 24 Volt electrical system with alternator, negative ground, and 24 Volt battery.
This machine has 24 Volt electrical system with alternator, negative ground, and 24 Volt battery.This machine has 24 Volt electrical system with alternator, negative ground, and 24 Volt battery.
This machine has 24 Volt electrical system with alternator, negative ground, and 24 Volt battery.
There are two basic circuits in the electrical system:
1. Charging circuit (alternator and battery).
2. Starting circuit (switch, solenoid, battery, and starter).
NOTE:NOTE:
NOTE:NOTE:
NOTE:Disconnect battery ground cable before making any repairs to electrical circuits.
In addition to the two basic circuits, there is an accessories circuit and operating light circuit(s).
ELECTRICAL SYSTEM INSPECTIONELECTRICAL SYSTEM INSPECTION
ELECTRICAL SYSTEM INSPECTIONELECTRICAL SYSTEM INSPECTION
ELECTRICAL SYSTEM INSPECTION
Check for:
- Clean and tight battery cables. Be sure all cables are clean and tight. Remove any acid or corrosion from
battery cables with baking soda and water solution. Cover terminals with grease to prevent corrosion.
- Proper tension on drive belt for alternator. For drive belt adjustment, see ALTERNATOR DRIVE BELT
ADJUSTMENT information.
- Loose wire connections. Be sure all wires are tightly connected.
- Broken or open wires. Replace any wires that are damaged or worn.
- Proper electrolyte level in battery. Add distilled water if necessary.
- Proper voltage of battery. Charge if necessary.
NOTE:NOTE:
NOTE:NOTE:
NOTE:See ELECTRICAL Section in Parts Manual for parts information, layouts and hookups.
BATTERY DISCONNECT SWITCHBATTERY DISCONNECT SWITCH
BATTERY DISCONNECT SWITCHBATTERY DISCONNECT SWITCH
BATTERY DISCONNECT SWITCH
Located on side of shrouding behind cab door.
Breaks positive circuit between battery and all points on
machine.
This switch should be used to disconnect battery circuit
when transporting machine and whenever false starts or
electrical damage need be prevented.
Turn switch to OFF to disconnect battery circuit.
Turn switch to ON to connect battery circuit.
WARNING WARNING
WARNING WARNING
WARNING
If welding is to be done on machine:If welding is to be done on machine:
If welding is to be done on machine:If welding is to be done on machine:
If welding is to be done on machine:
1)1)
1)1)
1)
Get factory authorization.Get factory authorization.
Get factory authorization.Get factory authorization.
Get factory authorization.
2)2)
2)2)
2)
Disconnect battery.Disconnect battery.
Disconnect battery.Disconnect battery.
Disconnect battery.
3)3)
3)3)
3)
Disconnect electronic throttle.Disconnect electronic throttle.
Disconnect electronic throttle.Disconnect electronic throttle.
Disconnect electronic throttle.
4)4)
4)4)
4)
Disconncet radio.Disconncet radio.
Disconncet radio.Disconncet radio.
Disconncet radio.
Damage to components will occur if theDamage to components will occur if the
Damage to components will occur if theDamage to components will occur if the
Damage to components will occur if the
above procedures are not followed.above procedures are not followed.
above procedures are not followed.above procedures are not followed.
above procedures are not followed.
ELECTRICAL SYSTEM MAINTENANCEELECTRICAL SYSTEM MAINTENANCE
ELECTRICAL SYSTEM MAINTENANCEELECTRICAL SYSTEM MAINTENANCE
ELECTRICAL SYSTEM MAINTENANCE
MasterMaster
MasterMaster
Master
ElectricalElectrical
ElectricalElectrical
Electrical
DisconnectDisconnect
DisconnectDisconnect
Disconnect
SwitchSwitch
SwitchSwitch
Switch