BASF 6106 - Page 4

l IST 0 F C 0 N T E N T S
SECTION
3.
3.1
INSTALLATION AND OPERATION
Installat ion
3.1.1 General
3.1.2
Unpacking and Inspection
3.1.3 Connecting Cables
3.1.4 Connectors
3.1.4.1 DC-Connector
3.1.4.2 Signal Connector
3.1.4.3 Frame Connector
3.1.4.4 Interconnecting Diagram
3.1.5 Logic Levels and Termination
3.1.6 Connecting Configuration
3.1.6.1 Single Drive Configuration
3.1.6.2 Multiple Drive Configuration
3.1.7 Selection of the Desired Option
3.1.7.1 Selection Options
3.1.7.2 Head Load Options
3.1.7.3 In Use / Disk Change Option
3.1.7.4 Door Lock Options
3.1.7.5 Activity LED Options
3.1.7.6 Write Protect Option
3.1.7.7 Stepper Motor Switching
3.1.7.8 Jumper Matrix
3.1.8 Drive Mounting
3.1.8.1 Mounting Positions
3.1.8.2 Mounting Dimensions
3.2 Operation
3.2.1 General
3.2.2
Mini Disk Storage and Handling
3.2.3 Write Protect
3.2.3.1 Write Protect if notch open
(optional)
3.2.3.2 Write Protect if notch covered
(ECMAl
4.
4.1
4.2
4.3
4.3.1
4.3.2
MAINTENANCE
General
Too1s and Test Equipment
Checks, Adjustment and
Replacements
PCS Replacement
Spindle Drive
System
PAGE
3-1
3-1
3-1
3-1
3-2
3-2
3-2
3-2
3-2
3-2
3-4
3-4
3-4
3-4
3-6
3-6
3-6
3-6
3-6
3-7
3-7
3-7
3-8
3-10
3-10
3-10
3-11
3-11
3-11
3-12
3-12
3-12
4-1
4-1
4-1
4-2
4-2
4-2
IV
SECTION
4.3.2.1 Drive Motor and Drive 8elt
Checks
4.3.2.2 Drive Belt Tension Check
4.3.2.3 Drive Belt Replacement and
Tension Adjustment
4.3.2.4 Drive Motor Speed Check
4.3.2.5 Drive Motor Speed Adjustment
4.3.2.6 Drive Motor Speed Adjustment
using a Frequency Counter
4.3.2.7 Drive Motor Replacement
4.3.3 Positioning System
4.3.3.1 Track Adjustment Check
4.3.3.2 Track Adjustment Procedure
4.3.3.3 Adjustment Check for Optical
Track
Zero Switch
4.3.3.5 Track Zero Switch Replacernent
4.3.3.6 Head Carriage Replacement
4.3.3.7 Head Load Pad Replacement (6106)
4.3.4 Head Load Mechanism
4.3.4.1 Head Load ~olenoid Replacement
4.3.4.2 Head load Actuator Check
4.3.5 Read/Write Electronics
4.3.5.1 Jitter Check and Adjustment
4.3.5.2 Read Amplitude Check
4.3.6
Photo Transistors and LED's
4.3.6.1 Photo Transistor Replacement
4.3.6.2 lED-Replacement
4.3.6.3 Index Detector Adjustrnent Check
4.3.6.4 Index Detector Adjustment
4.4 Location of Testpoints,
IC's,
Potentiornenters and Connectors
Spare Parts
PAGE
4-2
4-2
4-3
4-3
4-3
4-4
4-4
4-5
4-5
4-6
4-7
4-8
4-9
4-9
4-10
4-10
4-10
4-11
4-11
4-11
4-12
4-12
4-12
4-12
4-13
4-14
5.
5.1
Attachment
I, Spare Parts for BASF 6106
5.2 Attachment 2, Spare Parts for BASF 6108