Page 5;&(%$*4.8"4,7%<'*#$"&8#=%/7*,#*%4,77%>?@@@?@AA?BCDC1Item 56250
EF;6GHIJ6KFGLIMNFLMG6MFMO6 E6GPJ
R(&'89"83
GI%JK6!6MG%6T6OGKLO%E_IOY%FMU%U6FG_%;KIN%
LMOIKK6OG%RKIPMULMR%QLK6%OIMM6OGLIM-%
O.*4X%)"$.%,%<',7"2"*9%*7*4$("4",8%"2%V&'%,(*%"8%9&'+$%,#%$&%).*$.*(%$.*%&'$7*$%"#%/(&/*(7V%
3(&'89*91%%U&%8&$%5&9"2V%$.*%/&)*(%4&(9%/7'3%/(&W"9*9%)"$.%$.*%$&&71%%M*W*(%(*5&W*%$.*%
3(&'89"83%/(&83%2(&5%$.*%/7'31%%U&%8&$%'#*%$.*%$&&7%"2%$.*%/&)*(%4&(9%&(%/7'3%"#%9,5,3*91%%L2%9,5,3*9=%.,W*%
"$%(*/,"(*9%+V%,%#*(W"4*%2,4"7"$V%+*2&(*%'#*1%%L2%$.*%/7'3%)"77%8&$%2"$%$.*%&'$7*$=%.,W*%,%/(&/*(%&'$7*$%"8#$,77*9%+V%
,%<',7"2"*9%*7*4$("4",81
R(&'89*9%G&&7#-%G&&7#%)"$.%G.(**%J(&83%J7'3#
`?J(&83%J7'3%,89%I'$7*$
1. Tools marked with “Grounding Required” have
a three wire cord and three prong grounding
plug. The plug must be connected to a properly
grounded outlet. If the tool should electrically
malfunction or break down, grounding provides
a low resistance path to carry electricity away
from the user, reducing the risk of electric shock.
[E**%`?J(&83%J7'3%,89%I'$7*$1\
2. The grounding prong in the plug is connected
through the green wire inside the cord to the
grounding system in the tool. The green wire
in the cord must be the only wire connected to
the tool’s grounding system and must never
be attached to an electrically “live” terminal.
[E**%`?J(&83%J7'3%,89%I'$7*$1\
3. The tool must be plugged into an appropriate outlet,
properly installed and grounded in accordance
with all codes and ordinances. The plug and outlet
should look like those in the preceding illustration.
[E**%`?J(&83%J7'3%,89%I'$7*$1\
U&'+7*%L8#'7,$*9%G&&7#-%G&&7#%)"$.%G)&%J(&83%J7'3#
I'$7*$#%2&(%a?J(&83%J7'3
1. Tools marked “Double Insulated” do not
require grounding. They have a special
double insulation system which satisfies
OSHA requirements and complies with
the applicable standards of Underwriters
Laboratories, Inc., the Canadian Standard
Association, and the National Electrical Code.
2. Double insulated tools may be used in either of the
120 volt outlets shown in the preceding illustration.%%%
[E**%I'$7*$#%2&(%a?J(&83%J7'31\
6Z$*8#"&8%O&(9#
1. Grounded tools require a three wire extension cord.
Double Insulated tools can use either
a two or three wire extension cord.
2. As the distance from the supply outlet increases,
you must use a heavier gauge extension cord.
Using extension cords with inadequately sized wire
causes a serious drop in voltage, resulting in loss of
power and possible tool damage. [E**%G,+7*%F1\
3. The smaller the gauge number of the wire, the
greater the capacity of the cord. For example,
a 14 gauge cord can carry a higher current
than a 16 gauge cord. [E**%G,+7*%F1\
4. When using more than one extension cord
to make up the total length, make sure
each cord contains at least the minimum
wire size required. [E**%G,+7*%F1\
To Next Page
Loading...
