Beckman Coulter Allegra 6R User Manual (English)

Questions and Answers:

M
Melissa BurkeAug 15, 2025
What to do if Beckman Coulter Allegra 6R Laboratory Equipment rotor cannot achieve set speed?
- M
  Michael WagnerAug 15, 2025
  If the rotor speed of your Beckman Coulter Laboratory Equipment cannot reach the set speed, there are several potential causes and solutions: * **Low line voltage:** Measure the line voltage while the centrifuge is operating. * **Imbalance detector tripped:** Turn the POWER switch to OFF (O), wait 30 seconds, and then turn it back ON (I). * **Thermal protector tripped:** Turn the POWER switch to OFF (O), wait 60 seconds, and then turn it back ON (I). * **Electrical failure:** Check the connections. If the issue persists, further assistance is needed. * **Worn motor components or motor failure:** If the motor bearings, commutator are worn, or the motor has failed, further assistance is needed.
J
Jonathan LeblancAug 21, 2025
What to do if Beckman Coulter Allegra 6R Laboratory Equipment door will not open?
- K
  Kirsten RyanAug 21, 2025
  If the door of your Beckman Coulter Laboratory Equipment will not open, check the following: * **Power:** Ensure the power cord is plugged in and the POWER switch is set to ON (I). * **Rotor Speed:** Wait until the rotor completely stops spinning (below 40 rpm). * **Secondary Latch:** Verify that the secondary latch lever is in the UNLOCK position. * **Latch Stuck:** If the latch is stuck, follow the emergency access procedure.
A
Andre GeorgeAug 25, 2025
What to do if Beckman Coulter Allegra 6R Laboratory Equipment thermal cutoff switch activated?
- A
  Allison WrightAug 25, 2025
  If the thermal cutoff switch has been activated on your Beckman Coulter Laboratory Equipment, follow these steps: 1. Turn the TIME knob to OFF and press the POWER switch to OFF (O). 2. Verify that the ambient temperature is within the specified limits. 3. Inspect the air inlet for obstructions and check the air-inlet filters for dirt. Clean as necessary. 4. Allow the motor to cool down (approximately 15 minutes with the door open). Then, press the POWER switch to ON (I) to reset the thermal protector circuit. If the problem continues, further assistance is needed.
J
Jeremiah WongAug 28, 2025
How to fix chamber icing in Beckman Coulter Allegra 6R Laboratory Equipment?
- C
  Cathy KaneAug 28, 2025
  To address chamber icing in your Beckman Coulter Laboratory Equipment, especially in refrigerated models: * **Excess Humidity:** Wipe out any moisture from the chamber before each run. * **Condensation Buildup:** Prevent condensation between runs by: * Leaving the door open. * Setting the TEMPERATURE knob higher than the ambient temperature. * Turning the centrifuge power off.
C
Curtis LaneAug 31, 2025
What to do if Beckman Coulter Allegra 6R Laboratory Equipment set temperature cannot be achieved?
- L
  lgutierrezAug 31, 2025
  If the set temperature cannot be reached in your refrigerated Beckman Coulter Laboratory Equipment, consider the following: * **Ambient Temperature:** Reduce the ambient temperature. * **Run Duration:** Precool the rotor and extend the run time. * **Temperature Knob:** Adjust the temperature knob. * **Dirty Filter:** Clean the filter. * **Rotor Temperature:** Precool the rotor. * **Excess Moisture:** Wipe out any moisture in the chamber before each run. * **Gasket Issues or Refrigeration Problems:** Further assistance is needed.
J
Jeff SanchezSep 4, 2025
What to do if Beckman Coulter Allegra 6R chamber over-temperature?
- J
  Julie SmithSep 4, 2025
  If your refrigerated Beckman Coulter Laboratory Equipment chamber is over-temperature, take these steps: 1. Turn the TIME knob to OFF and press the POWER switch to OFF (O). 2. Ensure the ambient temperature is within the specified limits. 3. Check for any obstructions in the air inlet and clean the air-inlet filter if it's dirty. 4. Check the chamber temperature; if it remains over the expected temperature, further assistance is needed.
T
Travis JenkinsSep 7, 2025
What to do if Beckman Coulter Allegra 6R temperature cannot be maintained?
- A
  Andrew GarrisonSep 7, 2025
  If the temperature cannot be maintained in your refrigerated Beckman Coulter Laboratory Equipment, check these factors: * **Ambient Temperature:** Reduce the ambient temperature. * **Rotor Speed:** Reduce the rotor speed if it's higher than the rated speed. * **Dirty Filter:** Clean the filter. * **Refrigeration or Electronic Problem:** Further assistance is needed.