What to do if the door does not open on Beckman Coulter Allegra X-30 Laboratory Equipment?
If the door of your Beckman Coulter Laboratory Equipment doesn't open, first, wait until the rotor stops spinning. Then, ensure the power is on by plugging in the power cord and turning the power on. If the issue persists, it could be due to a source power failure or a stuck latch, in which case you should refer to Emergency Access instructions.
What to do if chamber does not reach selected temperature in Beckman Coulter Allegra X-30 Laboratory Equipment?
If your Beckman Coulter Laboratory Equipment chamber does not reach the selected temperature (refrigerated models), refer to the applicable rotor manual for temperature and speed requirements. Also, precool the rotors before running at low temperatures, or precool the rotor chamber by running a 30-minute cycle at the desired temperature with the speed set at 2000 rpm.
How to fix error during closing of door on Beckman Coulter Allegra X-30 Laboratory Equipment?
If you encounter an error during the closing of the door on your Beckman Coulter Laboratory Equipment, first, remove any debris in the latch. Then, try closing the lid quickly. If the problem persists, turn the power off (O), then back on (I) to reset the equipment.
What to do if “Door open” detected during run of Beckman Coulter Allegra X-30 Laboratory Equipment?
If a “Door open” is detected during a run with your Beckman Coulter Laboratory Equipment, after the rotor comes to a complete stop, shut the centrifuge door, turn the power off (O), then back on (I) to reset the equipment.
What to do if microprocessor or mechanical malfunction of Beckman Coulter Allegra X-30?
If you experience a microprocessor or mechanical malfunction with your Beckman Coulter Laboratory Equipment, after the rotor comes to a complete stop, open and close the centrifuge door, then restart.
How to fix Microprocessor or mechanical malfunction of Beckman Coulter Laboratory Equipment?
If you experience a microprocessor or mechanical malfunction with your Beckman Coulter Laboratory Equipment, after the rotor comes to a complete stop, turn the power off (O), then back on (I) to reset it.
Why are the displays blank on my Beckman Coulter Allegra X-30?
If the displays are blank on your Beckman Coulter Laboratory Equipment, first, ensure the power cord is properly plugged in and the power is turned on. If that doesn't work, it could be an electrical failure; ensure both ends of the power cord are securely connected and contact Beckman Coulter Field Service. A blown fuse could also be the cause, but system fuses cannot be replaced by the user, so contact Beckman Coulter Field Service.
Why TEMP °C display flashes on Beckman Coulter Allegra X-30 Laboratory Equipment?
If the TEMP °C display flashes on your Beckman Coulter Laboratory Equipment (refrigerated models), precool the rotors before running at low temperatures. You can also precool the rotor chamber by running a 30-minute cycle at the desired temperature with the speed set at about 2000 rpm. If a lower temperature deviation alert is required, contact Beckman Coulter Field Service.
General| Maximum Speed | 30, 000 RPM |
|---|---|
| Weight | 340 kg (750 lbs) |
| Capacity | 4 x 750 mL |
| Temperature Range | -10°C to +40°C |
| Drive System | Direct drive brushless motor |
| Refrigeration | Yes |
| Timer | Up to 99 hours, 59 minutes |
| Accel/Decel Profiles | 10 acceleration rates, 10 deceleration rates |
| Type | Benchtop centrifuge |
| Noise Level | <65 dBA at maximum speed |
| Programs | Up to 99 programmable settings |
| Display | LCD display |
| Power Requirements | 200-240 V, 50/60 Hz |
Defines various safety alert symbols (DANGER, WARNING, CAUTION, IMPORTANT, NOTE) used in the manual.
Provides crucial safety guidelines for installing and maintaining the centrifuge equipment.
Details safety measures related to electrical hazards, fire risks, and mechanical operations.
Advises on safe handling of chemical and biological materials during centrifuge use.
Details the power switch, control panel, system keys, program keys, and digital displays.
Guides users on how to set speed, time, temperature, and acceleration/deceleration rates.
Explains how to initiate a centrifuge run and how to stop it safely.
Introduces troubleshooting and explains how to interpret and respond to error messages.
Provides instructions for manual access to retrieve samples in case of power failure.
To Next Page