UK UK
70 71
DK DK
MONTERING AF BETRÆK
BEMÆRK! Sørg for ikke at vride eller krydse skulderselerne.
Følg trinene beskrevet ovenfor, men i omvendt rækkefølge, for at fastgøre
betrækket igen.
RENGØRING
Det er vigtigt kun at bruge de originale betræk, da de udgør en væsentlig del af
funktionen. Du kan kun få reservebetræk hos din forhandler.
BEMÆRK!
Vask betrækkene, før du bruger dem første gang.
• Betrækkene kan maskinvaskes ved maks. 30°C på nvask. Hvis du vasker det ved
højere temperatur, kan betrækket blive bleget.
• Vask betrækkene separat og lad dem lufttørre. Tør dem aldrig i tørretumbler!
• Tør dem ikke i direkte sollys!
• Plastikdelene kan rengøres med et mildt rengøringsmiddel og varmt vand.
ADVARSEL!
Brug under ingen omstændigheder kemiske rengørings- eller blegemidler!
ADVARSEL!
Det integrerede selesystem kan ikke fjernes fra autostolen. Fjern ikke dele af
selesystemet!
13 14
Cleaning
Care should be taken only to use an
original dk791 seat cover because
the cover is also an essential
functional component. Spare covers
can be obtained from your specialist
retailer.
WARNING! Never use harsh cleaning or bleaching agents!
WARNING! The belt system cannot be dismantled!
Never remove individual parts of the belt system!
You can clean the belts with a clean cloth and some lukewarm
soapy water. Try to avoid getting the belts too wet.
• Pull the headrest cover over the edge of the headrest and
remove.
• Thread the shoulder belts with the buckle tongue
s out of the
headrest cover.
• Remove the headrest cover, taking care not to damage the white
foams under neath the cover.
• Undo both press studs between the backrest cover and leg
support cover.
• Thread the belt buckle out of the leg support cover and then
remove it.
• Undo the press stud behind the sun visor.
• Now you can remove the backrest cover, taking care not to
damage the white protective foams underneath the cover.
WARNING! The infant car seat must under no circumstances be
used without the cover.
Note! Only DK791 original covers may be used.
Attaching the cover
Follow the steps described above but in reverse order in order to
re-fasten the cover.
Note! In doing so, do not twist or mix up the shoulder belts.
The cover consists of 6 parts: 1 backrest cover, 1 leg support
cover, 1 headrest cover, 1 belt buckle pad and 2 shoulder pads.
To remove, please apply the following procedure:
• Undo the belt buckle.
• Remove both shoulder pads from the belt.
RReemmoovviinngg tthhee ccoovveerr
Removing the cover
Product lifespan
Gradual wear of the plastic, for example caused by exposure to
sunlight (UV), can cause slight deterioration of the product’s
properties.
13 14
Cleaning
Care should be taken only to use an
original dk791 seat cover because
the cover is also an essential
functional component. Spare covers
can be obtained from your specialist
retailer.
WARNING! Never use harsh cleaning or bleaching agents!
WARNING! The belt system cannot be dismantled!
Never remove individual parts of the belt system!
You can clean the belts with a clean cloth and some lukewarm
soapy water. Try to avoid getting the belts too wet.
• Pull the headrest cover over the edge of the headrest and
remove.
• Thread the shoulder belts with the buckle tongue
s out of the
headrest cover.
• Remove the headrest cover, taking care not to damage the white
foams under neath the cover.
• Undo both press studs between the backrest cover and leg
support cover.
• Thread the belt buckle out of the leg support cover and then
remove it.
• Undo the press stud behind the sun visor.
• Now you can remove the backrest cover, taking care not to
damage the white protective foams underneath the cover.
WARNING! The infant car seat must under no circumstances be
used without the cover.
Note! Only DK791 original covers may be used.
Attaching the cover
Follow the steps described above but in reverse order in order to
re-fasten the cover.
Note! In doing so, do not twist or mix up the shoulder belts.
The cover consists of 6 parts: 1 backrest cover, 1 leg support
cover, 1 headrest cover, 1 belt buckle pad and 2 shoulder pads.
To remove, please apply the following procedure:
• Undo the belt buckle.
• Remove both shoulder pads from the belt.
RReemmoovviinngg tthhee ccoovveerr
Removing the cover
Product lifespan
Gradual wear of the plastic, for example caused by exposure to
sunlight (UV), can cause slight deterioration of the product’s
properties.
PRODUKTPLEJE
For at sikre, at din autostol giver den maksimale beskyttelse,
skal du overholde følgende:
• Alle autostolens vigtige dele bør kontrolleres regelmæssigt for skader.
• Kontrollér, at alle mekaniske komponenter fungerer korrekt.
• Det er yderst vigtigt at sikre, at autostolen ikke kommer i klemme mellem hårde
genstande som køretøjsdøre, sædeskinner osv., da dette kan føre til skader.
• Efter udsættelse for massive kræfter (fx efter en kollision), er det vigtigt, at
babyautostolen kontrolleres af producenten.
OBS: Det anbefales at købe et ekstra originalt betræk ved køb af babyautostolen, så
denne kan blive brugt selv når det ene betræk vaskes og tørres.
PRODUKTINFORMATION
Hvis du har spørgsmål, bedes du først kontakte din forhandler. Du skal have følgende
information klar:
• Serienummer (se mærkat under autostolen).
• Køretøjets mærke og model og placeringen af køretøjssædet, hvorpå autostolen
bruges.
• Barnets vægt, alder og højde.
17 18
Follow the instruction manual for your stroller!
You may attach the infant car seat on any approved stroller.
TRAVEL SYSTEM REMOVING THE COVER
The cover consists of 6 parts:
1 backrest cover, 1 newborn inlay
1 headrest cover, 1 belt buckle pad and 2 shoulder pads.
To remove, please apply the following procedure:
• Undo the belt buckle.
• Remove both shoulder pads from the belt.
WARNING! The infant car seat must under no circumstances be used
without the cover.
NOTE! Only original covers may be used.
Attaching the cover
NOTE!
Ensure to not twist or mix up the
shoulder belts.
Follow the steps described above
but in reverse order in order to
re-fasten the cover.
17 18
Follow the instruction manual for your stroller!
You may attach the infant car seat on any approved stroller.
TRAVEL SYSTEM REMOVING THE COVER
The cover consists of 6 parts:
1 backrest cover, 1 newborn inlay
1 headrest cover, 1 belt buckle pad and 2 shoulder pads.
To remove, please apply the following procedure:
• Undo the belt buckle.
• Remove both shoulder pads from the belt.
WARNING! The infant car seat must under no circumstances be used
without the cover.
NOTE! Only original covers may be used.
Attaching the cover
NOTE!
Ensure to not twist or mix up the
shoulder belts.
Follow the steps described above
but in reverse order in order to
re-fasten the cover.
To Next Page
Loading...