UK UK
16 17
ATTACHING THE COVER
NOTE! Ensure to not twist or mix up the shoulder belts.
Follow the steps described above but in reverse order in order to re-fasten the cover.
CLEANING
It is important to only use the original covers since this is an essential part of the
function. You may only obtain spare covers from your retailer.
NOTE! Please wash the covers before you use it the rst time.
• Seat covers are machine washable at max. 30°C on delicate cycle. If you wash it at
higher temperature, the cover fabric may lose color.
• Wash the covers separately and let it dry naturally. Never dry it mechanically!
• Do not dry the cover in direct sunlight!
• Plastic parts can be cleaned with a mild detergent and warm water.
WARNING!
Do not use chemical detergents or bleaching agents under any circumstances!
WARNING!
The integrated harness system cannot be removed from the car seat. Do not remove
parts of the harness system!
13 14
Cleaning
Care should be taken only to use an
original dk791 seat cover because
the cover is also an essential
functional component. Spare covers
can be obtained from your specialist
retailer.
WARNING! Never use harsh cleaning or bleaching agents!
WARNING! The belt system cannot be dismantled!
Never remove individual parts of the belt system!
You can clean the belts with a clean cloth and some lukewarm
soapy water. Try to avoid getting the belts too wet.
• Pull the headrest cover over the edge of the headrest and
remove.
• Thread the shoulder belts with the buckle tongue
s out of the
headrest cover.
• Remove the headrest cover, taking care not to damage the white
foams under neath the cover.
• Undo both press studs between the backrest cover and leg
support cover.
• Thread the belt buckle out of the leg support cover and then
remove it.
• Undo the press stud behind the sun visor.
• Now you can remove the backrest cover, taking care not to
damage the white protective foams underneath the cover.
WARNING! The infant car seat must under no circumstances be
used without the cover.
Note! Only DK791 original covers may be used.
Attaching the cover
Follow the steps described above but in reverse order in order to
re-fasten the cover.
Note! In doing so, do not twist or mix up the shoulder belts.
The cover consists of 6 parts: 1 backrest cover, 1 leg support
cover, 1 headrest cover, 1 belt buckle pad and 2 shoulder pads.
To remove, please apply the following procedure:
• Undo the belt buckle.
• Remove both shoulder pads from the belt.
RReemmoovviinngg tthhee ccoovveerr
Removing the cover
Product lifespan
Gradual wear of the plastic, for example caused by exposure to
sunlight (UV), can cause slight deterioration of the product’s
properties.
13 14
Cleaning
Care should be taken only to use an
original dk791 seat cover because
the cover is also an essential
functional component. Spare covers
can be obtained from your specialist
retailer.
WARNING! Never use harsh cleaning or bleaching agents!
WARNING! The belt system cannot be dismantled!
Never remove individual parts of the belt system!
You can clean the belts with a clean cloth and some lukewarm
soapy water. Try to avoid getting the belts too wet.
• Pull the headrest cover over the edge of the headrest and
remove.
• Thread the shoulder belts with the buckle tongue
s out of the
headrest cover.
• Remove the headrest cover, taking care not to damage the white
foams under neath the cover.
• Undo both press studs between the backrest cover and leg
support cover.
• Thread the belt buckle out of the leg support cover and then
remove it.
• Undo the press stud behind the sun visor.
• Now you can remove the backrest cover, taking care not to
damage the white protective foams underneath the cover.
WARNING! The infant car seat must under no circumstances be
used without the cover.
Note! Only DK791 original covers may be used.
Attaching the cover
Follow the steps described above but in reverse order in order to
re-fasten the cover.
Note! In doing so, do not twist or mix up the shoulder belts.
The cover consists of 6 parts: 1 backrest cover, 1 leg support
cover, 1 headrest cover, 1 belt buckle pad and 2 shoulder pads.
To remove, please apply the following procedure:
• Undo the belt buckle.
• Remove both shoulder pads from the belt.
RReemmoovviinngg tthhee ccoovveerr
Removing the cover
Product lifespan
Gradual wear of the plastic, for example caused by exposure to
sunlight (UV), can cause slight deterioration of the product’s
properties.
PRODUCT CARE
In order to ensure that your infant car seat provides the maximum protection you must
observe the following:
• All important parts of the infant car seat should be checked regularly for damage.
• Check that all mechanical components function properly.
• It is absolutely essential to ensure that the infant car seat is not jammed between
hard objects such as vehicle doors, seat rails etc., since this may lead to damage.
• After exposure to massive forces (e.g. after a collision), it is essential that the infant
car seat is checked by the manufacturer.
Note! It is advisable to buy an additional cover so that this seat can continue to be
used even when the cover is being washed and dried.
PRODUCT INFORMATION
If you have any questions, please contact your retailer rst. You should have the
following details ready:
• Serial number (see sticker underneath the car seat).
• Make and model of the vehicle and the position of the vehicle seat on which the
car seat is used.
• Weight, age and height of the child.
17 18
Follow the instruction manual for your stroller!
You may attach the infant car seat on any approved stroller.
TRAVEL SYSTEM REMOVING THE COVER
The cover consists of 6 parts:
1 backrest cover, 1 newborn inlay
1 headrest cover, 1 belt buckle pad and 2 shoulder pads.
To remove, please apply the following procedure:
• Undo the belt buckle.
• Remove both shoulder pads from the belt.
WARNING! The infant car seat must under no circumstances be used
without the cover.
NOTE! Only original covers may be used.
Attaching the cover
NOTE!
Ensure to not twist or mix up the
shoulder belts.
Follow the steps described above
but in reverse order in order to
re-fasten the cover.
17 18
Follow the instruction manual for your stroller!
You may attach the infant car seat on any approved stroller.
TRAVEL SYSTEM REMOVING THE COVER
The cover consists of 6 parts:
1 backrest cover, 1 newborn inlay
1 headrest cover, 1 belt buckle pad and 2 shoulder pads.
To remove, please apply the following procedure:
• Undo the belt buckle.
• Remove both shoulder pads from the belt.
WARNING! The infant car seat must under no circumstances be used
without the cover.
NOTE! Only original covers may be used.
Attaching the cover
NOTE!
Ensure to not twist or mix up the
shoulder belts.
Follow the steps described above
but in reverse order in order to
re-fasten the cover.
To Next Page
Loading...