Why Beko WTX71232W Washer machine stopped shortly after the programme started?
If your Beko washer stops shortly after starting, it might have temporarily stopped due to low voltage. It should resume running once the voltage returns to normal.
Why programme time does not countdown on Beko Washer?
If the programme time isn't counting down on your Beko washer (models with a display), the timer may pause during water intake until the machine takes in enough water. It may also stop during the heating step until the selected temperature is reached, or during the spinning step if the load is unbalanced.
Why washing takes longer time than specified in the manual in Beko WTX71232W?
If your Beko washer is taking longer than usual, it could be due to low water pressure, which causes the machine to wait until it takes in enough water. Low voltage or low input water temperature can also extend the washing time. Additionally, the machine may increase the amount of rinse water or add an extra rinse step. Excessive foam from too much detergent can also prolong the cycle.
How to start Beko WTX71232W after closing the door?
If your Beko washer isn't starting after you close the door, make sure you press the Start / Pause / Cancel button. Also, if you've loaded too much laundry, it can be difficult to close the door properly. Reduce the amount of laundry and ensure the door is securely closed.
Why is my Beko WTX71232W Washer vibrating so much?
If your Beko Washer vibrates excessively or makes unusual noises, it could be due to several reasons. Ensure the machine is level by adjusting the feet. A hard substance might be in the pump filter, so clean it. Remove the transportation safety bolts if you haven't already. Adjust the laundry quantity; too little or too much can cause imbalance. Also, make sure the machine isn't leaning on anything.
Why does my Beko WTX71232W Washer laundry remain wet after washing?
If your laundry remains wet after the programme ends in your Beko Washer, it might be due to excessive foam, which activates the automatic foam absorption system because too much detergent was used. Use the recommended amount of detergent.
What to do if my Beko Washer programme cannot be started or selected?
If the programme on your Beko Washer cannot be started or selected, it's possible that the machine has switched to self-protection mode due to a supply problem like line voltage or water pressure issues. To cancel the current programme, turn the Programme Selection knob to select another programme.
What to do if my Beko Washer enters standby mode or does not take in water?
If your Beko Washer enters standby mode or doesn't take in water, check the following: * Ensure the tap is turned on. * Make sure the water inlet hose isn't bent; flatten it if it is. * Clean the water inlet filter if it's clogged. * Close the loading door completely. * Verify the water connection and ensure water isn't cut off; if it was cut off, press Start/Pause after water is restored to resume.
Why is there water leaking from the bottom of my Beko WTX71232W?
If you notice water leaking from the bottom of your Beko Washer, it could be due to a clogged or twisted water drain hose; try cleaning or flattening the hose. Another possible cause is a clogged pump filter, so try cleaning the pump filter as well.
What to do if my Beko Washer loading door cannot be opened?
If the loading door of your Beko Washer cannot be opened, it might be due to a few reasons: * The door lock is activated because of the water level; drain the water by running the Pump or Spin programme. * The machine is heating or spinning; wait until the programme completes. * The child lock is engaged; wait a couple of minutes after the programme ends for deactivation. * The door may be stuck due to pressure; grab the handle and push and pull the door to release it.
General| Load Capacity | 7 kg |
|---|---|
| Energy Efficiency Class | A+++ |
| Spin Speed | 1200 rpm |
| Dimensions (H x W x D) | 84 cm x 60 cm x 49 cm |
| Color | White |
To Next Page
