Why did my Beko Washer stop shortly after the program started?
Your Beko Washer might have stopped temporarily due to low voltage. It will resume running when the voltage restores to the normal level.
Why won't my Beko Washer go to the spinning step?
Your Beko Washer might not switch to the spinning step because: * There might be unbalanced load in the machine. The automatic unbalanced load detection system might be activated due to the unbalanced distribution of the laundry in the drum. * The machine will not spin if water is not drained completely. Check the filter and the draining hose. * Excessive foam might have occurred and automatic foam absorption system might have been activated due to too much detergent usage. Use recommended amount of detergent.
Why is my Beko WTX61031W leaking water from the bottom?
If you notice water leaking from the bottom of your Beko washing machine, it could be due to: * A clogged or twisted water drain hose. Clean or flatten the hose. * A clogged pump filter. Clean the pump filter.
What to do if my Beko WTX61031W Washer enters standby mode or doesn't take in water?
If your Beko Washer enters standby mode or doesn't take in water, consider the following: * The tap may be turned off. Turn on the taps. * The water inlet hose may be bent. Flatten the hose. * The water inlet filter may be clogged. Clean the filter. * The loading door may be open. Close the door. * The water connection may be wrong or water may be cut off (When the water is cut off, washing or rinsing LEDs flash). Check the water connection. If the water is cut off, press the Start/Pause key after the water has been supplied again to resume the operation from standby mode.
What to do if the loading door of my Beko WTX61031W Washer cannot be opened?
If the loading door of your Beko Washer cannot be opened, it could be due to the following reasons: * The door lock is activated because of the water level in the machine. Drain the water by running the Pump or Spin programme. * The machine is heating up the water or it is at the spinning cycle. Wait until the programme completes. * The child lock is engaged. The door lock will be deactivated a couple of minutes after the programme has come to an end, so wait for a couple of minutes for deactivation of the door lock. * The loading door may be stuck because of the pressure it is subjected to. Grab the handle and push and pull the loading door to release and open it.
What to do if my Beko Washer program does not start after closing the door?
If your Beko Washer program doesn't start after closing the door: * Ensure the Start / Pause / Cancel button was pressed. Press the Start / Pause / Cancel button. * The loading door may be difficult to close in case of excessive loading. Reduce the amount of laundry and make sure that the loading door is closed properly.
Why is foam overflowing from the detergent drawer of my Beko WTX61031W Washer?
If foam is overflowing from the detergent drawer of your Beko Washer: * Too much detergent is used. Mix 1 tablespoonful softener and ½ l water and pour into the main wash compartment of the detergent drawer. * Put detergent into the machine suitable for the programmes and maximum loads indicated in the 'Programme and consumption table'.
Why did oily stains appear on my laundry after washing in my Beko WTX61031W?
If oily stains appeared on your laundry after washing in your Beko Washer, it could be because regular drum cleaning is not applied. Clean the drum regularly.
Why do my clothes smell unpleasant after washing in my Beko WTX61031W?
If your clothes smell unpleasant after washing in your Beko Washer, it might be because odours and bacteria layers are formed on the drum as a result of continuous washing at lower temperatures and/or in short programmes. Leave the detergent drawer as well as the loading door of the machine ajar after each washing.
Why is my Beko WTX61031W Washer vibrating and making noise?
Your Beko Washer might be vibrating or making noise due to several reasons: * The machine might be standing unbalanced. Adjust the feet to level the machine. * A hard substance might have entered into the pump filter. Clean the pump filter. * Transportation safety bolts are not removed. Remove the transportation safety bolts. * Laundry quantity in the machine might be too little. Add more laundry to the machine. * The machine might be overloaded with laundry. Take out some of the laundry or distribute the load by hand. * The machine might be leaning on a rigid item. Make sure that the machine is not leaning on anything.
Safety guidelines for product usage and property protection.
Precautions to ensure children's safety around the washing machine.
Guidelines for safe electrical connections and usage.
Information on waste electrical and electronic equipment disposal.
Details on recyclable packaging materials.
Procedures for installing the washing machine, including location and connections.
Steps for sorting, preparing, loading laundry, and energy saving.
Guide to control panel, programmes, speed, delayed start, and end of cycle.
Instructions for routine cleaning of components like the drum, filters, and drawer.
Solutions for issues like failure to start, drain, or excessive noise.
Addresses problems like gray laundry, odors, and poor stain removal.
Safety guidelines for product usage and property protection.
Precautions to ensure children's safety around the washing machine.
Guidelines for safe electrical connections and usage.
Information on waste electrical and electronic equipment disposal.
Details on recyclable packaging materials.
Procedures for installing the washing machine, including location and connections.
Steps for sorting, preparing, loading laundry, and energy saving.
Guide to control panel, programmes, speed, delayed start, and end of cycle.
Instructions for routine cleaning of components like the drum, filters, and drawer.
Solutions for issues like failure to start, drain, or excessive noise.
Addresses problems like gray laundry, odors, and poor stain removal.
General| Door hinge | Left |
|---|---|
| Water fill | Cold |
| Control type | Rotary, Touch |
| Display type | LED |
| Loading type | Front-load |
| Certification | CE |
| Drum material | Stainless steel |
| Product color | White |
| Built-in display | Yes |
| Appliance placement | Freestanding |
| Drum capacity | 6 kg |
| Cycle time (max) | 240 min |
| Delay start (max) | 9 h |
| Residual moisture | 62 % |
| Spin-drying class | C |
| Maximum spin speed | 1000 RPM |
| Noise level (spin) | 78 dB |
| Noise level (wash) | 63 dB |
| Load balancing system | No |
| Number of washing programs | - |
| Current | 10 A |
| Connected load | 2200 W |
| AC input voltage | 230 V |
| AC input frequency | 50 Hz |
| Power consumption (off) | 0.25 W |
| Power consumption (standby) | 0.75 W |
| Energy consumption washing per cycle | 0.78 kWh |
| Annual water consumption washing | 8799 L |
| Annual energy consumption washing | 152 kWh |
| Package type | Box |
Weight and Dimensions| Depth | 490 mm |
|---|---|
| Width | 600 mm |
| Height | 840 mm |
| Weight | 57000 g |
To Next Page
