Why is there water in my Beko Washer?
If you see water in your Beko Washer, some water might have remained in the product due to the quality control processes in the production. This is not a failure; water is not harmful to the machine.
How to open the loading door of my Beko Washer?
If the loading door of your Beko Washer won't open, it could be due to several reasons: * The door lock is activated because of the water level; drain the water by running the Pump or Spin programme. * The machine is heating up the water or is at the spinning cycle; wait until the programme completes. * The child lock is engaged; wait a couple of minutes for deactivation of the door lock. * The loading door may be stuck because of the pressure; grab the handle and push and pull the loading door to release and open it.
Why does my Beko WTX81031W enter standby mode or not take in water?
If your Beko Washer enters standby mode or doesn't take in water, check the following: * Ensure the tap is turned on. * Make sure the water inlet hose is not bent; flatten it if it is. * Clean the water inlet filter if it's clogged. * Ensure the loading door is closed properly. * Check the water connection. If the water is cut off, press the Start/Pause key after the water has been supplied again to resume the operation from standby mode.
Why won't my Beko WTX81031W Washer switch to the spinning step?
If your Beko Washer doesn't switch to the spinning step, the automatic unbalanced load detection system might be activated due to the unbalanced distribution of the laundry in the drum. Also, the machine will not spin if water is not drained completely, so check the filter and the draining hose. Excessive foam might have occurred, and the automatic foam absorption system might have been activated due to too much detergent usage, so use the recommended amount of detergent.
What to do if my Beko WTX81031W Washer does not start after closing the door?
If your Beko Washer program does not start after closing the door, it may be because the Start / Pause / Cancel button was not pressed, so press the Start / Pause / Cancel button. Also, it may be difficult to close the loading door in case of excessive loading, so reduce the amount of laundry and make sure that the loading door is closed properly.
Why did my Beko Washer stop shortly after the program started?
If your Beko Washer stopped shortly after the programme started, the machine might have stopped temporarily due to low voltage. It will resume running when the voltage restores to the normal level.
Why can't I start or select a programme on my Beko Washer?
If a programme cannot be started or selected on your Beko Washer, the washing machine has switched to self protection mode due to a supply problem (line voltage, water pressure, etc.). To cancel the programme, turn the Programme Selection knob to select another programme. The previous programme will be canceled.
Why has the color of my clothes faded after washing in my Beko Washer?
If the color of clothes faded after washing in your Beko Washer, it may be because excessive laundry was loaded in, so do not load the machine in excess. Also, the detergent in use may be damp, so keep detergents closed in an environment free of humidity and do not expose them to excessive temperatures. Finally, a higher temperature may be selected, so select the proper programme and temperature according to the type and soiling degree of the laundry.
Why is there too much foam in my Beko WTX81031W Washer?
If too much foam is forming in your Beko Washer, it could be due to: * Using improper detergents for the washing machine, so use detergents appropriate for the washing machine. * Using an excessive amount of detergent, so use only a sufficient amount of detergent. * Detergent was stored under improper conditions, so store detergent in a closed and dry location and do not store in excessively hot places. * Some meshed laundry such as tulle may foam too much because of their texture, so use smaller amounts of detergent for this type of item. * Detergent is put in the wrong compartment, so put the detergent in the correct compartment. * Softener is being taken early, so there may be problem in the valves or in the detergent dispenser. Call the Authorised Service Agent.
Why is my Beko Washer vibrating and making noise?
If your Beko Washer is vibrating or making noise, here are a few things to check: * Ensure the machine is level by adjusting the feet. * Remove the transportation safety bolts. * If a hard substance has entered the pump filter, clean the pump filter. * Adjust the laundry quantity: if it is too little, add more laundry; if it is overloaded, take some out or distribute the load evenly. * Make sure the machine isn't leaning on anything.
General| Capacity | 8 kg |
|---|---|
| Spin Speed | 1400 RPM |
| Energy Efficiency Class | A+++ |
| Weight | 70 kg |
| Programs | 15 |
| Color | White |
| Type | Front Load |
To Next Page
