Beko WTX71232WI User Manual

Beko WTX71232WI

60 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

2820525918_IT / 27-05-17.(15:14)

Lavatrice

Manuale utente

WTX71232WI

IT / EN

Numero del documento=

Washing Machine

User’s Manual

Table of Contents

Questions and Answers:

C
Catherine GardnerSep 6, 2025
Why washing performance is poor and laundry turns gray in Beko WTX71232WI?
- A
  Alice PetersSep 6, 2025
  If your laundry turns gray after washing in your Beko washer, it could be due to using too little detergent over time, washing at low temperatures for too long, or using insufficient detergent with hard water. Using too much detergent, overloading the machine, selecting the wrong program and temperature, or using the wrong type of detergent can also cause this issue. Use the recommended amount of original detergent appropriate for water hardness and the laundry, and select the proper program and temperature.
D
Dalton PriceSep 5, 2025
Why Beko WTX71232WI machine stopped shortly after the programme started?
- D
  Daniel BarnesSep 5, 2025
  If your Beko washer stops shortly after starting, it might have temporarily stopped due to low voltage. It should resume running once the voltage returns to normal.
R
Robert LamSep 4, 2025
Why programme time does not countdown on Beko WTX71232WI Washer?
- Z
  zhawkinsSep 5, 2025
  If the programme time isn't counting down on your Beko washer (models with a display), the timer may pause during water intake until the machine takes in enough water. It may also stop during the heating step until the selected temperature is reached, or during the spinning step if the load is unbalanced.
K
Kurt MullenSep 4, 2025
Why washing takes longer time than specified in the manual in Beko WTX71232WI Washer?
- B
  Bradley SimpsonSep 4, 2025
  If your Beko washer is taking longer than usual, it could be due to low water pressure, which causes the machine to wait until it takes in enough water. Low voltage or low input water temperature can also extend the washing time. Additionally, the machine may increase the amount of rinse water or add an extra rinse step. Excessive foam from too much detergent can also prolong the cycle.
J
Joshua GreenAug 23, 2025
What to do if the Beko WTX71232WI Washer loading door cannot be opened?
- T
  tcampbellAug 25, 2025
  If your Beko washer door won't open, it could be due to a few reasons. The door lock may be activated because of the water level; drain the water by running the Pump or Spin program. The machine might be heating water or spinning; wait until the program completes. If the child lock is engaged, wait a couple of minutes after the program ends for it to deactivate. The door might also be stuck due to pressure; try pushing and pulling the door to release it.
B
Brittany BellSep 2, 2025
Why is my Beko WTX71232WI Washer vibrating so much?
- G
  Gary PattersonSep 2, 2025
  If your Beko Washer vibrates excessively or makes unusual noises, it could be due to several reasons. Ensure the machine is level by adjusting the feet. A hard substance might be in the pump filter, so clean it. Remove the transportation safety bolts if you haven't already. Adjust the laundry quantity; too little or too much can cause imbalance. Also, make sure the machine isn't leaning on anything.
J
Joshua LunaSep 1, 2025
Why does my Beko Washer laundry remain wet after washing?
- R
  roberthansenSep 1, 2025
  If your laundry remains wet after the programme ends in your Beko Washer, it might be due to excessive foam, which activates the automatic foam absorption system because too much detergent was used. Use the recommended amount of detergent.
J
Jay TaylorSep 1, 2025
What to do if my Beko Washer programme cannot be started or selected?
- H
  hughescrystalSep 1, 2025
  If the programme on your Beko Washer cannot be started or selected, it's possible that the machine has switched to self-protection mode due to a supply problem like line voltage or water pressure issues. To cancel the current programme, turn the Programme Selection knob to select another programme.
N
Nicole AlvaradoAug 31, 2025
What to do if my Beko WTX71232WI Washer enters standby mode or does not take in water?
- J
  josephbeckerAug 31, 2025
  If your Beko Washer enters standby mode or doesn't take in water, check the following: * Ensure the tap is turned on. * Make sure the water inlet hose isn't bent; flatten it if it is. * Clean the water inlet filter if it's clogged. * Close the loading door completely. * Verify the water connection and ensure water isn't cut off; if it was cut off, press Start/Pause after water is restored to resume.
L
Luis BrownAug 30, 2025
Why is there water leaking from the bottom of my Beko WTX71232WI?
- J
  Jacob DayAug 30, 2025
  If you notice water leaking from the bottom of your Beko Washer, it could be due to a clogged or twisted water drain hose; try cleaning or flattening the hose. Another possible cause is a clogged pump filter, so try cleaning the pump filter as well.

Beko WTX71232WI Specifications

General

Type	Front Load
Load Capacity	7 kg
Energy Efficiency Class	A+++
Spin Speed	1200 rpm
Color	White
Programs	15

Related product manuals

Preview: Beko WTX71232W

Preview: Beko WTX61031W

Preview: Beko WTX91032W

Preview: Beko WTX61032W

Preview: Beko WTX91232WI

Beko WTX91232WI

Preview: Beko WTX81432WI

Beko WTX81432WI

Preview: Beko WTXS61232WI

Beko WTXS61232WI

Preview: Beko WTX91486AI-IT

Beko WTX91486AI-IT

Beko WTX101486AI-IT

Preview: Beko WTB820E1W