Belanger DuoScrubber HP

Questions and Answers

K
Karen SampsonAug 11, 2025
Why does the cleaning head stall when scrubbing wheels on my Belanger DuoScrubber HP?
- B
  Becky WrightAug 11, 2025
  If the cleaning head stalls while the Belanger Cleaning Equipment is scrubbing wheels, this may be due to the pressure of the regulators on the air panel being set too high. Check the pressure on the regulator from the air control panel. If the regulated pressure is too high, it may cause the head to stall. Release pressure by turning the knob counterclockwise until stalling halts, ensuring there is still enough pressure to allow the heads to rotate smoothly.
D
Donna ColemanAug 16, 2025
What to do if my Belanger DuoScrubber HP experiences excessive vibration?
- S
  Shane CarrollAug 16, 2025
  Excessive vibration in your Belanger Cleaning Equipment can stem from a couple of issues. First, ensure that the DuoScrubber® HP is tightly lagged to the floor. Also, check for play in the pivot arm bearings; if there's evident sloppiness, the bearings will need replacement.
B
bestbrettAug 23, 2025
Why are the cleaning heads not spinning on my Belanger Cleaning Equipment?
- D
  david13Aug 23, 2025
  If the cleaning heads on your Belanger Cleaning Equipment aren't spinning, it could be due to a mechanical failure or a tripped motor control circuit breaker. Check to see if the bearings are seized up and replace if necessary. If not, try resetting the motor circuit breaker.
J
jodi88Aug 28, 2025
What causes the cleaning fingers on B-Pads to collapse inward on Belanger Cleaning Equipment?
- S
  Stephanie RiveraAug 29, 2025
  If the cleaning fingers on the B-Pads of your Belanger Cleaning Equipment are collapsing inward, it's likely that the wrong B-Pads (CW or CCW) have been installed on the head(s). Refer to the illustrations for the correct installation of the B-Pads and confirm that the CW and CCW B-Pads are on the appropriate head assemblies, adjusting as necessary.
K
Kristin WilsonSep 3, 2025
What to do if cleaning heads will not retract on Belanger Cleaning Equipment?
- L
  Luis HarveySep 3, 2025
  If the cleaning heads on your Belanger Cleaning Equipment will not retract, it could be due to a faulty electrical signal or a faulty MAC valve. Check the electrical signal. To check the valve, remove the airline from ports 2 and 3 of the 4-way valve and jog the toggle switch on the controller on and off. If air is not felt when switching from 2 and 3, then the valve is bad.

Summary

Operational Warning

Chemical Warnings

Lists dangerous chemicals and warns about potential warranty voidance if used.

Important Safety Information - MUST READ

Safety Symbols and Signal Words

Explains safety alert symbols and signal words (Danger, Warning, Caution) used in the manual.

Before You Begin

Specifies that only trained individuals should perform installation, maintenance, or service.

Read the Manual

Emphasizes reading and understanding the manual before proceeding with any work.

Installation

Identify Conveyor

Explains how to identify conveyor types (single/double guide rail, width) for proper positioning.

Tunnel Placement Overview

Provides an overview of tunnel placement, including dimensions and orientation considerations.

Height Adjustment

Details how to adjust the cleaning head height for proper conveyor clearance and floor proximity.

Rotation of Cleaning Heads

Specifies the correct rotation direction for driver and passenger side cleaning heads for effective cleaning.

Utilities

Overview of Water and Pneumatic Connections

Water Connections

Provides step-by-step instructions for connecting water lines from the pumping station to the units.

Pneumatic Connections

Details the pneumatic circuit for connecting the air panel to the cylinders on the units.

Electrical Connections: Air Panel to Controller

Explains how to supply power to the air regulation panel from the carwash controller.

Initial Air Settings for Air Panel

Provides guidelines for setting initial air pressure for extend and retract functions.

Electrical Connections: Motor Plate Utilities

Covers wiring the motors to the main power source, including voltage considerations.

Maintenance

Trouble Shooting

Provides solutions for common problems like head stalling, not spinning, retract issues, vibration, and finger collapse.

Rotation of B-Pad Cleaning Heads

Illustrates correct clockwise (CW) and counterclockwise (CCW) rotation for cleaning heads.