Belanger SUDZAMELEON ARCH

Questions and Answers

G
grojasAug 16, 2025
What to do if Belanger Cleaning Equipment chemical has no chemical delivery?
- T
  Teresa TapiaAug 16, 2025
  If your Belanger Cleaning Equipment is not delivering chemicals, try the following: * Clean or replace the foot valve. * Fill the storage tank. * Prime the chemical pump. * Check for proper operating voltage.
T
tracy35Aug 20, 2025
Why are Belanger Cleaning Equipment wall washers not turning on?
- D
  Daniel WelchAug 20, 2025
  If the wall washers on your Belanger Cleaning Equipment are not turning on, check the following: * Ensure electrical connections are secure at both the Wall Washer and Air Plenum. * Check the main power connections. * Verify that the Controller has been programmed properly.
I
Isaac HoAug 23, 2025
Why are Belanger Cleaning Equipment leg and Foam Bullet® LEDs not turning on or off?
- A
  Alexis GillAug 25, 2025
  If the LEDs on your Belanger Cleaning Equipment's Leg Assembly & Foam Bullet® are not turning on or off, the issue might be due to loose electrical connections. Verify that the electrical connections are secure both at the component and at the Utility Panel. If the connections are secure and the LEDs still do not function, consider replacing the LED light assembly.
J
jasonandersonAug 27, 2025
How to fix Belanger Cleaning Equipment wall washers that are in an incorrect position?
- J
  johnsonpatriciaAug 28, 2025
  If the wall washers on your Belanger Cleaning Equipment are in an incorrect position (likely not adjusted during installation), manually rotate the Wall Washers on the Pivot Brackets to direct light onto bubbles and the vehicle.
J
Julie EstradaAug 31, 2025
How to fix Belanger Cleaning Equipment fan that is not working?
- J
  Joseph VasquezAug 31, 2025
  To troubleshoot a non-working fan in your Belanger Cleaning Equipment: * Check the power supply to the fan. * Ensure the wire connections are correct in the Fan Enclosure. * Verify that the Controller has been programmed properly.
B
Brittany AustinSep 4, 2025
Why are Belanger Cleaning Equipment wall washers not turning off?
- J
  Joshua SilvaSep 4, 2025
  If the wall washers on your Belanger Cleaning Equipment are not turning off, the issue may be related to the controller program. Verify that the Controller has been programmed properly.
P
Pamela PatelSep 8, 2025
Why is Belanger Cleaning Equipment fan speed incorrect?
- E
  evansemilySep 8, 2025
  If the fan speed on your Belanger Cleaning Equipment is incorrect: * Check to make sure the wire connections are correct in the Fan Enclosure. * Verify that the Controller has been programmed properly.
W
willie53Nov 11, 2025
What to do if Belanger Cleaning Equipment chemical delivery is pulsating or weak spray?
- A
  Andrew JenningsNov 11, 2025
  If you observe a pulsating or weak spray in your Belanger Cleaning Equipment's chemical delivery system, take the following steps: * Ensure the Spray Bayonet Nozzles are pointing downward toward the center finger of the Tri Nozzles. * Clean the Bayonet Nozzle by removing it from the Tri Nozzle and using a thin wire. * Check the check valve on the Bayonet Nozzle to ensure the arrow points toward the spray nozzle. * Disassemble the Bayonet Nozzle, clean its components, and reassemble with pipe dope. * Clean the nozzles on the Leg Manifold Covers with a thin wire after removing the covers. * Clean the screen of the Foam Bullet® by removing its cover and blowing off any film, then clean the nozzles with a thin wire. * Ensure all fittings in the system are tight and leak-free. * ...