EasyManuals Logo

BFT VIRGO Installation Manual

BFT VIRGO
18 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #14 background imageLoading...
Page #14 background image
INSTALLATION MANUAL
external release lever (Fig.1 ref.”S”).
1) Insert the release key and turn it clockwise (Fig.19 ref.”1”).
2) Move lever “S” until the lock is released (Fig.19 ref.”2”).
3) Keep the lever in the release position by turning the key clockwise
(Fig.19 ref.”3”).
4) Push the leaf slowly to open or close the gate.
To reactivate motor-driven operation, turn the key clockwise to free the
lever from its released position, then return it to its initial position for
normal operation.
18) MANUAL WIRE RELEASE DEVICE (Fig.13)
The manual emergency release can be operated by a wire device:
- Take all the metal cable out of the sheath and insert it into the release
lever.
- Lock the sheath and suitably adjust its position by means of the
appropriate screw.
- The cover is provided with a section to be torn o for the sheath to
go through.
- For further information, refer to the specic instructions for the release
device.
19) VIRGO BAT KIT INSTALLATION
- Fix the SBS board on the back of the panel box by means of a screw,
as indicated in Fig.14.
- Fix the board protection box (Fig.14 - “C”) supplied with the kit.
-
Position the two batteries on the supports, as indicated in Fig.14 (“A”).
- Secure the batteries using the bracket and screws supplied.
- Proceed to wire the SBS board with reference to the diagram in Fig.14.
20) AUTOMATION CHECK
Before allowing the automation to be used normally, carry out the
following procedure very carefully:
 Checkthecorrectfunctioningofall safetydevices(limitmi-
croswitches, photocells, sensitive edges etc.).
• Checkthatthethrust(anti-squash)forceoftheleafiswithinthelimits
set by current regulations.
• Checkthemanualopeningcommand.
• Checktheopeningandclosingoperationswiththecontroldevices
in use.
• Checkthestandardandcustomisedelectronicfunctioninglogic.
21) AUTOMATION OPERATION
Since the automation can be remote-controlled by means of a remote
control device or a start button, and so out of sight, the good working
order of all the safety devices should be checked regularly. In the event
of any anomalous functioning of the safety devices, consult a speciali-
sed technician immediately. Keep children at a safe distance from the
automation operation area.
22) CONTROL
The automation is used for the power-operated opening and closing of the
gate. The control can be of a number of types (manual, remote-controlled,
magnetic badge access control, etc.) depending on requirements and
the characteristics of the installation. See the specic instructions for
the various control systems. Users of the automation must be instructed
about its control and operation.
23) MAINTENANCE
Disconnect the power supply when carrying out any maintenance
operations.
• LubricatetheVIRGOs of the manoeuvring arm regularly.
• Cleanthelensesofthephotocellseverysooften.
• Haveaqualiedperson(installer)checkcorrectmotortorquesetting.
• Intheeventofanyanomalousfunctioningwhichcannotberesolved,
disconnect the power supply and contact a specialised technician
(installer). Whilst the automation is out of order, activate the manual
release to allow manual opening and closing.
22 - VIRGO
D811415_09

Other manuals for BFT VIRGO

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the BFT VIRGO and is the answer not in the manual?

BFT VIRGO Specifications

General IconGeneral
Power Supply230 V
Motor Voltage24 V
Max Leaf Length2.5 m
Max Leaf Weight200 kg
Max Gate Weight400 kg
Max Gate Length5 m
TypeElectromechanical
Safety DevicesPhotocells

Related product manuals