BGS technic 959 - User Manual

SW-Stahl und Werkzeugvertriebs GmbH Tel. +49 (0) 2191 / 46438-0
F 56 essartS resukreveL ax +49 (0) 2191 / 46438-40
ed.lhatsws@ofni :liaM-E diehcsmeR 79824-D
Instruction Manual
BGS technic KG
Bandwirkerstr. 3
42929 Wermelskirchen
Tel.: 02196 720480
Fax.: 02196 7204820
mail@bgs-technic.de
www.bgstechnic.com
Art. 959
Torque Wrench
HOW TO USE
A. Balancing wrench in hand with graduations visible with the marked arrow Elementary Scale up
then unlock knurled handle by turning lock nut counter clockwise.
B. Set amount of torque required by turning knurled handle to read exact
amount on case graduations.
EXAMPLE: 20Nm
1. Turn knurled handle until the zero graduation on the bevel edge of
the knurled handle is lined up with the vertical mark on the case and
is even with the 19Nm graduation.
2. Turn knurled handle clockwise until 1,0Nm graduation on the level
edge of the handle is in line with the vertical line on the case.
3. Lock handle securely by turning lock nut clockwise, and now wrench
is set at 20Nm which is ready to use .
C. lnstall the proper socket or attachmant to the square drive and apply to
nut or ball and pull handle until you feel and / or hear wrench click.
Release pull and wrench automatically resets for next operation.
Do not continue to pull after wrench releases. Use special care at low
torque settings that will pull stop when wrench clicks.
CAUTION
1. If wrench has not been used or has been in storage for some time, operate it several times at a
low torque setting which permits special internal lubricant to re-coat internaI working parts.
2. When wrench is not in use, keep doing adjustment at lowest torque setting.
3. Do not turn handle below lowest torque setting.
4. Do not continue pulling on the wrench after pre-set torque has been reached and the wrench has
been released. Pressure must be taken off the handle and the wrench allowed to automatically
reset itself, continuing to apply pressure after the wrench has been released, will result in damage
to the part being torque by applying more than the specified amount of torque.
5. Tool is rugged and designed for shop use, but is also a precision measuring instrument and
should be treated as such.
6. Clean wrench by wiping .Do not immerse in any type of cleaner which may affect special high
pressure lube with which the wrench is packed at the factory.
7. This torque wrench was calibrated and tested before leaving the factory and is accurate to ±4%.
8. The wrench is only suitable for measuring torque 5 to 25 Nm
This is a precisions measuring instrument.
Calibration and servicing must be done regularly and is the owner responsibility.

Summary

How to Use Torque Wrench

Balancing and Unlocking Wrench

Balance wrench with graduations visible, unlock knurled handle counter-clockwise.

Setting Torque Amount

Turn knurled handle to set required torque using case graduations.

Applying Torque and Reset

Install socket, pull handle until click. Release pull; wrench resets automatically.

Cautions and Operational Guidance

Initial Use and Storage

Operate at low torque for lubrication. Store at lowest torque setting.

Safe Operation Limits

Do not turn below lowest setting or continue pulling after release to prevent damage.

Tool Care and Accuracy

Clean by wiping; do not immerse. Wrench calibrated to +/-4% accuracy; service regularly.

Conversion Tables and Formulas

Conversion Tables

Tables for converting Foot Pounds, Kilogramm Meters, and Newton Meters.

Conversion Formulas

Formulas for converting units like CMKG, MKG, Nm, and Ft/Lb.

BGS technic 959 Specifications

General

Brand	BGS technic
Model	959
Category	Power Tool
Language	English