What causes water to leak from the drain valve of my BIG ASS FANS Fan?
If water is leaking from the drain valve, check for a worn washer or stem, or an open drain valve. Replace the washer or replace the drain valve.
Why is my BIG ASS FANS COOL-SPACE 300 motor overheating and shutting off?
If the motor overheats, shuts off, and restarts, it could be due to an extension cord with too small a gauge or obstructed inlet air. Try replacing the extension cord with a heavier one and ensure there is at least 3 ft (0.9 m) of clearance for inlet air. If the problem continues, consider replacing the motor.
What to do if my BIG ASS FANS Fan is not running and makes a humming sound?
If your fan won't run but is humming, the blade might be hitting the shroud, or the motor might be stalled. Try re-centering the blade hub. If the motor will not turn by hand, you may need to replace it.
What does E2 error mean on my BIG ASS FANS COOL-SPACE 300 Fan?
The E2 error indicates overcurrent protection. This means the current draw is too high. You should check the extension cord size, ensure the motor spins freely, and verify that airflow is not obstructed.
What does E5 error mean on my BIG ASS FANS COOL-SPACE 300 Fan?
The E5 error indicates overload protection, meaning the motor is running too hot. Check that airflow is not obstructed and verify the extension cord size.
Why is the floor wet near my BIG ASS FANS COOL-SPACE 300 cooler?
If the floor is wet at the side of the cooler, the water inlet hose might be loose at the supply hose or at the bulkhead fitting. Tighten the connections and/or replace the hose washers.
Why is water overflowing from my BIG ASS FANS COOL-SPACE 300 Fan reservoir?
If water is overflowing from the reservoir or spitting through the fan, it could be due to several reasons: a loose float valve hose, water pressure that's too high (exceeding 120 PSI), or a float valve that's not properly seated. Try tightening the hose connections and/or replacing the hose washers. If the water pressure is too high, reduce it by adding an inline reducer. Also, check all hoses for leaks.
What to do if there are too many dry streaks on the pads of my BIG ASS FANS COOL-SPACE 300?
If there are too many dry streaks on the pads, check for blocked holes in the spray bar or adjust the water flow. Remove the spray bar and plug, then clean the tube and holes. Also, open the water flow control valve.
What to do if my BIG ASS FANS COOL-SPACE 300 Fan blade does not turn and cooler makes squealing sound?
If the fan blade doesn't turn and the cooler makes a squealing sound, the motor might be stalled. You may need to replace the motor.
Why is my BIG ASS FANS Fan not reaching full speed?
If the fan turns but doesn't reach full speed and makes a humming sound, check the capacitor (where visible) and motor electrical connections. You may need to replace the capacitor or motor, or replace the extension cord with a heavier cord if it is too small.
Connect the cooler to a water source using a standard garden hose.
Connect the cooler to a fused or breaker-protected circuit.
Key factors for optimal cooler placement including air supply and ventilation.
Step-by-step guide to filling, pump activation, and fan operation.
Explanation of indicators, buttons, and functions on the control panel.
Detailed explanation of each button on the remote control for operation.
Procedures for cleaning cooling media and the water sump for optimal performance.
Guidance on using water treatment tablets to prevent mineral buildup.
Common issues and solutions for the pump motor and operation.
Issues and solutions related to water flow, leaks, and spray bar performance.
Common problems and solutions for the fan motor, blade, and electrical connections.
Explanation of error codes and their corresponding solutions for the Cool-Space 500.
Contact details, address, and phone number for customer support.
Information on obtaining replacement parts and accessories.
General| Brand | BIG ASS FANS |
|---|---|
| Model | COOL-SPACE 300 |
| Category | Fan |
| Language | English |
To Next Page