Binatone Spirit 110 - User Manual

9. P(Pause) button
Spirit 110
Unpacking your phone
Corded Telephone
1. Where to find it
2. Installation
1. Locating the Base unit
The Base unit should be placed on a level surface, in a position where:
 the telephone line cable will reach your telephone line socket or
extension socket.
 it is not close to a sink, bath or shower, or anywhere else where
 it is not close to other electrical equipment - fridges, washing
machines, microwave ovens, TVs, fluorescent lights, etc.
2. Plug the coiled handset
cord into the Handset.
Plug the other end into
the jack on the left
side of the Base unit.
3. Place the Handset in
the Base unit.
4.
5.
Lift the Handset and check for Dial tone
in the earpiece.
Always use the
telephone line
cord supplied
with your
Spirit 110 phone.
Other telephone
line cords may
not work.
Make sure the plugs
click into place.
to Modular
Wall jack
2. Installation
it might get wet.
Making a
1
Lift the Handset, listen for a dial tone.
2 Dial the telephone number you wish to call.
3
To end the call, return the Handset to the
call
Lift the handset to answer call.
To answer a
call
Replace the Handset on the Base unit cradle.
To end a call
3. Telephone Operation
Base unit.
Last Number
1
Lift the Handset to redial the last number.
2
Press LNR button.
Redial
Ö The phone automatically dials the last
number you called (maximum of 32 digits).
Mute
During a call press and hold the
(MUTE)
button.
Function
Ö
When the mouthpiece is muted, the person
at the other end of the call cannot hear you
but you can hear his side.
2
To get back to the call, release the
button.
Use on PBX
Press R (RECALL) button on your
If you are using your Spirit 110 phone on a
RECALL
;
(MUTE)
Spirit 110 phone.
PBX,and the PBX user guide tells you to press
Inserting a
Pressing PAUSE button immediately after the
Pause in
For some switchboard system, an access
the dialing
sequence
access number, a pause of about 3.6 seconds
will be entered, and the desired number can
Press PAUSE button to insert a pause when
dialing or storing Long Distance Access Codes.
Telphone Operation continue...
1
2
be dialed immediately.
number must be dialed (usually an 8 or 9) to
get another dial tone and an outside line.
In the box you will find:
• Base Unit
• Handset
• Coiled Handset cord
• Telephone line cord
for Base unit
• User manual
Keep the packing
materials in a safe
place in case you later
need to transport
Keep your sales (till)
receipt, which is your
guarantee.
the unit.
3. STO (Store)button
4. MEM button
1
7
8
2
3
4
5
6
1.
is ringing
for an incoming call.
Ringer light
- This flashes when the phone
2. M1,M2 and M3 one -Touch Memory Buttons
5. LNR(Last Number Redial) button
6. Mute button
7. R(Recall) button
8. P(Pause) button
Plug one end of the telephone line cord the jack at the back of the
base unit and the other end into modular wall jack.

Summary

Installation

Locating the Base unit

Guidance on selecting an optimal location for the base unit.

Telephone Operation

Making a call

Instructions for initiating a telephone call.

To answer a call

Steps to take when receiving an incoming call.

To end a call

Procedure for terminating an ongoing call.

Last Number Redial

How to redial the last dialed number.

Mute Function

Instructions on using the mute function during a call.

Use on PBX

Guidance for operating the phone on a Private Branch Exchange (PBX).

Inserting a Pause in the dialing sequence

How to insert a pause in dialing sequences, e.g., for access codes.

Technical details

Standard

Specifies the phone model and standard.

Temperature range

Defines the operating and storage temperature limits.

PBX compatibility

Details compatibility with Private Branch Exchange systems.

Network connection

Information on network connection and country usage.

Connection and conditions for use

Instructions for connecting the phone and usage conditions.

Guarantee and service

Binatone Spirit 110 Specifications

General

Design	Compact
Ringer Volume	Adjustable
Dialing Type	Tone/Pulse
Display	LCD
Phonebook entries	50
Ringer volume levels	3
Caller ID	Yes
Call Waiting	Yes
Redial	Yes
Handset Volume Control	Yes
Color Options	White
Power Source	Telephone Line