To Next Page
A
Amy HoodSep 16, 2025
What to do if my Binder Oven has no chamber function (dark display)?
- MMarissa WilliamsSep 16, 2025
If there is no chamber function (dark display) on your Binder Oven, deactivate standby mode.
What to do if my Binder Oven has no chamber function (dark display)?
If there is no chamber function (dark display) on your Binder Oven, deactivate standby mode.
Why am I getting a pressure alarm on my Binder VDL without a vacuum connection?
If you encounter a pressure alarm when operating your Binder Oven without a vacuum connection, turn off pressure control.
Why are menu functions not available on my Binder Oven?
If menu functions are not available on your Binder Oven, log in with the required higher authorization.
What to do if acknowledging the alarm does not cancel the alarm state on my Binder Oven?
If acknowledging the alarm on your Binder Oven does not cancel the alarm state, remove the cause of the alarm. If the alarm state continues, contact BINDER service.
What to do if my Binder Dryer chamber is permanently turned off?
If the chamber of your Binder Dryer is permanently turned off, there are several potential causes. First, check the connection to the power supply and ensure the correct voltage (115V or 230V) is being supplied. Confirm that the oven is connected to the compressed air supply. Also, inspect the chamber fuse. If the safety device has turned off the oven, allow it to cool down, press the “RESET” button, and check the temperature set-point and safety device setting, selecting a suitable limit value if needed. If the safety device is defective, contact BINDER Service.
Why is the chamber of my Binder Dryer permanently turned off?
The chamber of your Binder Dryer might be permanently turned off due to several reasons. These include: a missing power supply, incorrect voltage (should be 115V or 230V), the oven not being connected to a compressed air supply, a tripped chamber fuse, or the safety device having shut off the oven. In the last case, allow the oven to cool and press the reset button, checking the temperature set-point and safety device settings. If the safety device is defective, contact BINDER Service.
How to fix a Binder Dryer chamber that is permanently turned off?
To address a Binder Dryer chamber that is permanently turned off: - Check the connection to the power supply. - Verify the voltage is correct (115V or 230V). - Ensure the oven is connected to the compressed air supply. - Inspect the chamber fuse. - If the safety device has shut off the oven, let it cool, press the reset button, and verify the temperature set-point and safety device settings, choosing an appropriate limit if necessary. - If the safety device is faulty, contact BINDER Service.
What to do if my Binder oven displays an 'Overtemperature' alarm and doesn't heat up?
If your Binder oven displays an 'Overtemperature' alarm and isn't heating, the safety temperature limiter (TL) may have turned off the heater. Allow the chamber to cool down, then acknowledge the alarm on the controller and restart the oven by reconnecting the power plug. If the error repeats, turn off the oven and contact BINDER service.
Why doesn't my Binder VDL heat up and shows alarm message „safety controller“?
If your Binder Oven chamber doesn’t heat up and shows the alarm message „safety controller“ on the controller display, it indicates that the safety controller has responded because the inner chamber temperature reached the safety controller value. This could be due to a safety controller value set too low, a temperature set-point too high, or an error in the heating system. To resolve this, let the chamber cool down, acknowledge the alarm on the controller, and check the settings of the temperature setpoint and safety controller value. If necessary, select a suitable safety controller value.
Why does my Binder VDL have no chamber function (dark display)?
If your Binder oven has no chamber function and the display is dark, the chamber might be in standby mode. Deactivate standby mode.
General
