7
VERY THIN 63SS 63P PE 4.5 7.5 10.0 5.0 563
14–16 Sec.— No. 2 Zahn 63ASS 63P PE 5.1 8.7 12.2 11.0 563A
Wash Primers, Dyes, Stains, 63BSS 63PB PE 9.0 14.3 20.0 14.0 563A
Solvents, Water, Inks 66SS 66S SE 3.4 5.0 9.0 565
66SS 66SD SE 7.9 12.1 10.5 565
66SS 66SK SE 11.0 15.2 19.5 13.0 565
63BSS 200 PI 3.1 5.2 6.4 12.0 563A
THIN 63ASS 63P PE 5.1 8.7 12.2 11.0 563A
16–20 Secs.—No. 2 Zahn 66SS 66SK SE 11.0 15.2 19.5 13.0 565
Sealers, Primers, 63BSS 200 PI 3.1 5.2 6.4 12.0 563A
Lacquers, Inks, Lubricants 63CSS PI 3.9 5.5 7.4 9.0 563A
Zinc Chromates, Acrylics
MEDIUM 63BSS 63PB PE 9.0 14.3 20.0 14.0 563A
19–30 Secs.—No. 2 Zahn 63CSS 63PR PE 9.5 15.5 19.5 18.0 563A
Lacquers, Syn. Enamels 66SS 66SD SE 7.9 12.0 11.0 565
Varnishes, Shellacs, Fillers, 66SS 66SK SE 11.0 15.2 19.5 13.0 565
Primers, Epoxies, Urethanes 63CSS 200 PI 3.1 5.2 6.4 12.0 563A
Lubricants, Wax Emulsions 66SS PI 3.9 5.5 7.4 9.0 565
HIGH SOLIDS
Enamels 65SS 63PR PE 9.5 15.5 19.5 18.0 565
HEAVY (CREAM-LIKE)
Over 28 Secs.—No. 4 Ford 67SS 67PB PE 9.5 14.9 19.5 12.0 567
House Paint, Wall Paint (Oil, Latex), 68SS 68PB PE 9.5 14.1 19.1 12.0 568
Block Sealers, Mill Whites, 67SS 206 PI 6.0 9.5 13.0 15.0 567
Vinyls, Acrylics, Epoxies, Gel Coats 68SS 201 PI 4.6 6.8 9.1 11.0 568
VERY HEAVY 68SS 68PB PE 9.5 14.1 19.1 12.0 568
Unaggregated, Block Fillers, 68SS 206 PI 6.2 9.8 13.2 15.0 568
Textured Coatings, Fire Retardants, 59ASS 242 PI 4.1 6.0 8.2 6.0 559
Road Marking Paint, Bitumastics, 59ASS 244 PI 7.8 11.5 15.2 12.0 559
Cellular Plastisols, Underbody, 59BSS 250 PI 7.3 11.0 14.7 RD 559
Roof Coatings 59BSS 252 PI 7.8 11.5 15.2 6.0 559
59CSS 262 PI 7.3 11.0 14.7 6.0 559
ADHESIVES 63CSS 63PB PE 9.0 14.3 20.0 14.0 563A
Waterbase 66SS 63PR PE 9.5 15.5 19.5 15.0 565
White Vinyl Glue 67SS 67PB PE 9.5 14.1 19.1 12.0 567
Solvent Base 63SS 66SD PE 7.9 12.1 16.2 4.0 563
Neoprenes 63ASS 66SD PE 7.9 12.1 16.2 7.0 563A
(Contact Cements) 66SS 66SD-3 PE 9.5 14.2 19.0 10.0 565
66SS 66SDJG PE 10.4 8.0-9.0 565
66SS 66R PE/SE 4.2 RD 565
66 66SDJG PE 10.4 8.0-9.0 565
L6SS 66SD-3 PE 9.5 14.2 19.0 10.0 565
L3BSS 66SD-3 PE 9.5 14.2 19.0 10.0 563A
CERAMICS & SIMILAR 63CVT 66PH PE 11.5 16.4 22.0 13.0 563CVT
ABRASIVE MATERIALS 64VT 64PA PE 12.1 15.0 21.0 13.0 564VT
Glazes, Engobes 67VT 67PD PE 10.0 15.0 20.0 15.0 567VT
Porcelain Enamel 68VT 68PB PE 9.5 14.1 19.1 12.0 568VT
CONCRETE CURING 66SS 200 PI 3.1 5.2 6.4 15.0 565
COMPOUNDS 67SS 206 PI 6.0 9.5 13.0 18.0 567
68SS 206 PI 6.2 9.8 13.2 20.0 568
MULTICOLOR 66SS 200 PI 3.1 5.2 12.0 565
PAINTS 67SS 206 PI 6.0 9.5 15.0 567
66SSxR3 PI 4.2 FAN 565
66SSxR8 PI 4.2 FAN 565
TEFLONS 63ASS 63PB PE 9.0 14.3 20.0 10.0 563A
63BSS 63PR PE 9.5 15.5 19.5 15.0 563A
66SS 66SD SE 7.9 12.1 7.0 565
HAMMERS 63CSS 63PB PE 9.0 14.3 14.0 563A
66SS 63PB PE 9.0 14.3 14.0 565
66SS 66SD SE 7.9 12.1 7.0 565
WRINKLE ENAMELS 63CSS 63PB PE 9.0 14.3 20.0 10.0 563A
66SS 63PB PE 9.0 14.3 20.0 10.0 565
ZINC RICH COATINGS 67VT 67PB PE 9.5 14.1 19.1 12.0 567VT
NOZZLE SELECTION CHART
CFM AT
MAX.
TYPE OF FLUID FLUID AIR TYPE PAT.
FLUID
TO BE SPRAYED NOZZLE NOZZLE * 30 50 70 (inches)
Needle
PSI PSI PSI AT 8 in.
No.★
FLUID NOZZLE ORIFICE SIZES
++ + + +
59ASS 59BSS 59CSS 63SS 63ASS 63BSS 63CSS 63CVT 64VT 66SS 67SS 67VT 68SS 68VT 794
.171 .218 .281 .028 .040 .046 .052 .052 .064 .070 .086 .086 .110 .110 .040
All air nozzles shown in combination with these (+) fluid nozzles can also be used in combination with any other fluid nozzle marked (+)
*See text Section B, page 6, for type code. ★All standard needles listed are stainless steel.
To Next Page
Loading...
