Binks 95G - Parts List; Maintenance

7
ITEM PART
NO. NO. DESCRIPTION QTY.
ITEM PART
NO. NO. DESCRIPTION QTY.
1
*
AIR CAP ASSEMBLY...................... 1
2
*
FLUID NOZZLE............................... 1
3 54-918
▲ SEALING RING............................... 1
4 54-4233 HEAD INSERT ................................ 1
5 54-4369
▲ HEAD INSERT SEAL RING ............. 1
6 54-4227 95G GRAVITY FEED HANDLE
ASSEMBLY .................................. 1
7 54-4359 TRIGGER STUD .............................. 1
8 82-126 TRIGGER SCREW ........................... 1
9 54-4364
● SIDE PORT CONTROL
ASSEMBLY
(Standard).................... 1
10 54-3511
▲ RETAINING RING........................... ✕
11 20-6160▲ O-RING .......................................... ✕
12 20-4615▲ O-RING .......................................... 2
13 54-3515 HOUSING....................................... 2
14 54-3520
▲ SPRING (Yellow)............................... 1
15 54-3512
▲ SPINDLE ASSEMBLY...................... 1
16 54-3518
▲ SPRING (Blue).................................. 2
17 54-3541 HOUSING....................................... 1
18
*
FLUID NEEDLE............................... 1
19 54-3871 GUNNERS MATE OIL .................... 1
20 192219 PLASTIC COATED GUN HOOK ..... 1
21 54-3606 MATERIAL VALVE
CONTROL KNOB ......................... 1
22 54-768 AIR CONNECTION ......................... 1
23 54-4439† AIR CONNECTION
1/4 BSP
(Not Shown)
................................... 1
24 54-4360 TRIGGER ........................................ 1
25 54-4370
▲ SEAL CARTRIDGE ASSEMBLY....... 1
26 54-3513 VALVE SPINDLE CAP..................... 1
27 54-4720 1 LITER GRAVITY FEED CUP
ASSEMBLY .................................. 1
28 GFC-404
■ DISPOSABLE LID ASSEMBLY
(Quantity 2 supplied / 54-4720) ............ 1
29 GFC-403 GRAVITY FEED CUP
SUB-ASSEMBLY
(Aluminum) .......... ✕
30 82-221 CLEANING BRUSH (Flat) ................. 1
31 54-4213
★ WRENCH
(Optional)
......................... 1
32 82-469 GUN BRUSH
(Round) ....................... 1
33 KGP-13
▲➤ CUP GASKET (Blue)......................... 1
34 KGP-5
♦ FILTER............................................ 1
35 OMX-70✓ DISPOSABLE LINER
(Not Shown)
(Refer to Service Bulletin SBBI-4-043)
PARTS LIST
(When ordering, please specify Part No.)
*
See Air and Fluid Nozzle Chart on Page 5.
▲ Part of Repair Kit 54-3589 Spare Parts Kit.
● Available as optional Quick Change Side Port Control 54-4365.
✕ Available as part of its assembly.
†
European gun assemblies only.
■ Available in 54-4715 Disposable Lid Kit (quantity of 2) only.
★ Not furnished. Please order separately.
➤ Available in 54-4717 Cup Gasket (Blue) Kit (quantity of 5) only.
♦ Available in 54-4716 Filter Kit (quantity of 5) only.
✓ Available in OMX-70-K48 Disposable Liner Kit (quantity of 48) only.
MAINTENANCE
TO REPLACE AIR VALVE
AND SPINDLE ASSEMBLY
Remove air valve control knob (21), spring (16), and
fluid needle (18). Unscrew housing (17) and remove
spindle assembly (15) with springs (14 & 16), seal
retainers (13), and o-rings (12). Lubricate new
o-rings with Gunners Mate. Assemble components using
material needle. Place this assembly along with Housing
(17) into gun body and screw into position. Remove
material needle and tighten housing.
TO REPLACE FLUID
CARTRIDGE ASSEMBLY
Remove material valve control knob (21), spring (16),
and remove fluid needle (18). Pull back trigger (24) and
remove seal cartridge assembly (25).
Remove and discard plastic packing pin in new seal
cartridge assembly. Pull back trigger and insert new
seal cartridge assembly. Reassemble fluid needle (18),
spring (16), and material valve control knob (21).