Binks Signature Series - Nozzle and Needle Selection Charts; Fluid Type and Nozzle Selection; Orifice Size Guide

8
Nozzle No. 59ASS 59BSS 59CSS 63SS 63ASS 63BSS 63CSS 65SS 66SS 67SS 68SS
Orifice Size .171 .218 .281 .028 .040 .046 .052 .059 .070 .086 .110
NOZZLE and NEEDLE SELECTION CHARTS
VERY THIN 63ss x 63P PE 4.5 7.5 10.0 5 663
14-16 secs. Zahn 2 Cup 63Bss x 63PB PE 9.0 14.3 20.0 14 663A
Wash primers, dyes, 66ss x 66SD SE 7.9 12.1 — 10.5 665
stains, solvents, 66ss x 66SK SE 11.0 15.2 19.5 13 665
w
ater, inks 63Bss x 200 PI 3.1 5.2 6.4 12 663A
THIN 63Ass x 63P PE 5.1 8.37 12.2 11 663A
16-20 secs. Zahn 2 Cup 63Bss x 63PE PE 9.5 15.0 20.0 13 663A
Sealer, lacquers, primers, 66ss x 66SK SE 11.0 15.2 19.5 13 665
inks, lubricants, 63Bss x 200 PI 3.1 5.2 6.4 12 663A
zinc chromates, acrylics
MEDIUM 63Bss x 63PB PE 9.0 14.3 20.0 14 663A
19-30 secs. Zahn 2 Cup 63Css x 63PE PE 9.5 15.0 20.0 13 663A
Synthetic enamels, varnishes, 66ss x 66SD SE 7.9 12.1 — 11 665
shellacs, fillers, primers, 66ss x 66SK SE 11.0 15.2 19.5 13 665
epoxies, urethanes, lubricants, 63Css x 200 PI 3.1 5.2 6.4 12 663A
wax emulsions, enamels
HEAVY 67ss x 67PB PE 9.5 14.9 19.5 12 667
(Cream-like) 68ss x 68PB PE 9.5 14.1 19.1 12 668
Over 28 secs. No. 4 Ford Cup 67ss x 206 PI 6.0 9.5 13.0 15 667
VERY HEAVY 68ss x 68PB PE 9.5 14.1 19.1 12 668
Texture coatings, 68ss x 206 PI 6.2 9.8 13.2 15 668
Road marking paint 59Ass x 244 PI 7.8 11.5 15.2 12 659
59Ass x 245 PI 7.8 11.5 15.2 6 659
59Bss x 251 PI 7.8 11.5 15.2 12 659
59Bss x 252 PI 7.8 11.5 15.2 6 659
59Css x 262 PI 7.3 11.0 14.7 6 659
68ss x 206 PI 6.2 9.8 13.2 15 668
ADHESIVES 63Bss x 66SD-3 PE 7.9 12.1 16.2 4 663
Waterbase white vinyl glues 67ss x 67PB PE 9.5 14.1 19.1 12 667
Solvent base, neoprenes 66ss x 66SD-3 PE 7.9 12.1 16.2 10 665
(contact cement) 66ss x 66SDJG PE 10.4 ——8-9 665
66ss x 66R PE/SE — 4.2 — RD 665
L6SS x 66SD-3 PE 9.5 14.2 19.0 10 665
L3BSS x 66SD-3 PE 9.5 14.2 19.0 10 663A
CERAMICS 67VT x 67PD PE 10.0 15.0 20.0 15 667VT
Similar abrasive materials, 68VT x 68PB PE 9.5 14.1 19.1 12 668VT
glazes, engobes,
porcelain enamel
BUFFING COMPOUNDS 64VT x 64PA PE 12.1 15.0 21.0 13 664VT
67VT x 67PD PE 10.0 15.0 20.0 15 667VT
CONCRETE CURING 66ss x 200 PI 3.1 5.2 6.4 15 665
COMPOUNDS
67ss x 206 PI 6.0 9.5 13.0 18 667
68ss x 206 PI 6.2 9.8 13.2 20 668
MULTICOLOR PAINTS 66ss x 200 PI 3.1 5.2 — 12 665
67ss x 206 PI 6.0 9.5 — 15 667
66ss x R3 PI — 4.2 — FAN 665
66ss x R8 PI — 4.2 — FAN 665
TEFLONS 63Ass x 63PB PE 9.0 14.3 20.1 10 663A
66ss x 66SD PE 7.9 12.1 —7 665
HAMMERS 63ss X 63PB PE 9.0 14.3 — 14 663A
66ss X 63PB PE 9.0 14.3 — 14 665
66ss X 66SD PE 7.9 12.1 —7 665
WRINKLE ENAMELS 63Css x 63PB PE 9.0 14.3 20.0 10 663A
66ss x 63PB PE 9.0 14.3 20.0 10 665
ZINC RICH COATINGS 66ss x 67PD PE 12.0 18.0 24.0 15 665N
67VT x 67PB PE 9.5 14.1 19.1 12 667VT
Note: PE - Pressure External SP - Siphon External PI - Pressure Internal
TYPE OF FLUID FLUID NOZZLE CFM AT MAX FLUID NEEDLE NOS.
TO BE SPRAYED X AIR TYPE 30 50 70 PATTERN FOR SPRAY GUN
NOZZLES PSI PSI PSI AT 8" MODEL 95