To Next PageTo Next PageWhat to do if Biostar Motherboard system does not boot from a hard disk drive?
First, check the cable running from the disk to the disk controller board, ensuring both ends are securely plugged in. Also, verify the drive type in the standard CMOS setup. It's also important to remember to back up your hard drive, as hard disks can fail at any time.
What to do if Biostar Motherboard system cannot boot after installing a second hard drive?
First, ensure that the master/slave jumpers are set correctly. Next, run the SETUP program and select the correct drive types. If issues persist, contact the drive manufacturers to verify compatibility with the other drives.
What to do if Biostar G41 HD Motherboard system is inoperative but keyboard lights are on?
Using even pressure on both ends of the DIMM, press down firmly until the module snaps into place.
How to troubleshoot Biostar Motherboard when there is no power in the system?
First, make sure the power cable is securely plugged in. If the issue persists, replace the cable. If problems continue, contact technical support.
Shows system information including BIOS version and build date.
Displays system memory size, excluding VGA shard memory.
Allows setting the system's internal clock.
Allows setting the system's date, automatically updating the day.
Displays CPU information and allows advanced CPU settings.
Configures the Super IO chipset, serial/parallel ports, and power-on settings.
Shows system temperature, fan speed, and voltage information.
Allows control of CPU and system fan speeds based on temperature.
Manages ACPI settings like suspend modes and wake-up events.
Configures USB controller modes, legacy support, and mass storage settings.
Clears the NVRAM (CMOS) data to reset BIOS settings.
Determines whether the OS or BIOS initializes PnP cards.
Controls how long a PCI device holds the bus before yielding.
Assigns an IRQ for the PCI VGA card.
Allows older graphics controllers to snoop on the VGA palette.
Toggles the onboard IDE controller's DMA transfer capability.
Allows manual assignment of system interrupts (IRQs) and DMA channels.
Specifies the sequence for booting from available devices.
Configures the boot order for installed hard disk drives.
Configures the boot order for removable media drives.
Configures the boot order for CD/DVD drives.
Adjusts boot-related settings like Quick Boot and Logo display.
Provides access to North Bridge and South Bridge configuration options.
Configures memory remapping, memory hole, and graphics adapter settings.
Manages USB functions, audio, and onboard LAN settings.
Controls CPU power supply for energy saving purposes.
Allows adjustment of the CPU's operating frequency.
Selects the control method for the PCIe clock.
Allows adjustment of the PCIe clock frequency.
Allows adjustment of the CPU's voltage.
Allows adjustment of the memory voltage.
Allows adjustment of the chipset voltage.
Allows adjustment of the DRAM clock speed.
Enables or disables DRAM timing configuration via SPD.
Sets the CAS Latency timing for DRAM.
Sets the Row Address Strobe (RAS) timing for DRAM.
Sets the Row Precharge Time (tRP) for DRAM.
Sets the Row Address to Column Address Delay (tRCD) for DRAM.
Sets the Write Recovery Time (tWR) for DRAM.
Sets the Refresh Cycle Time (tRFC) for DRAM.
Sets the Write to Read Delay (tWTR) for DRAM.
Sets the Row to Row Delay (tRRD) for DRAM.
Sets the Read to Precharge Time (tRTP) for DRAM.
Saves all configuration changes to CMOS and exits the setup utility.
Abandons all current changes and exits the setup utility.
Abandons current changes, restoring previously saved values.
Reloads factory default settings to resolve system issues.
Allows setting or revising supervisor and user passwords.
Shows system information including BIOS version and build date.
Displays system memory size, excluding VGA shard memory.
Allows setting the system's internal clock.
Allows setting the system's date, automatically updating the day.
Displays CPU information and allows advanced CPU settings.
Configures the Super IO chipset, serial/parallel ports, and power-on settings.
Shows system temperature, fan speed, and voltage information.
Allows control of CPU and system fan speeds based on temperature.
Manages ACPI settings like suspend modes and wake-up events.
Configures USB controller modes, legacy support, and mass storage settings.
Clears the NVRAM (CMOS) data to reset BIOS settings.
Determines whether the OS or BIOS initializes PnP cards.
Controls how long a PCI device holds the bus before yielding.
Assigns an IRQ for the PCI VGA card.
Allows older graphics controllers to snoop on the VGA palette.
Toggles the onboard IDE controller's DMA transfer capability.
Allows manual assignment of system interrupts (IRQs) and DMA channels.
Specifies the sequence for booting from available devices.
Configures the boot order for installed hard disk drives.
Configures the boot order for removable media drives.
Configures the boot order for CD/DVD drives.
Adjusts boot-related settings like Quick Boot and Logo display.
Provides access to North Bridge and South Bridge configuration options.
Configures memory remapping, memory hole, and graphics adapter settings.
Manages USB functions, audio, and onboard LAN settings.
Controls CPU power supply for energy saving purposes.
Allows adjustment of the CPU's operating frequency.
Selects the control method for the PCIe clock.
Allows adjustment of the PCIe clock frequency.
Allows adjustment of the CPU's voltage.
Allows adjustment of the memory voltage.
Allows adjustment of the chipset voltage.
Allows adjustment of the DRAM clock speed.
Enables or disables DRAM timing configuration via SPD.
Sets the CAS Latency timing for DRAM.
Sets the Row Address Strobe (RAS) timing for DRAM.
Sets the Row Precharge Time (tRP) for DRAM.
Sets the Row Address to Column Address Delay (tRCD) for DRAM.
Sets the Write Recovery Time (tWR) for DRAM.
Sets the Refresh Cycle Time (tRFC) for DRAM.
Sets the Write to Read Delay (tWTR) for DRAM.
Sets the Row to Row Delay (tRRD) for DRAM.
Sets the Read to Precharge Time (tRTP) for DRAM.
Saves all configuration changes to CMOS and exits the setup utility.
Abandons all current changes and exits the setup utility.
Abandons current changes, restoring previously saved values.
Reloads factory default settings to resolve system issues.
Allows setting or revising supervisor and user passwords.
General| Brand | Biostar |
|---|---|
| Model | G41 HD |
| Category | Motherboard |
| Language | English |
