ENGLISH
BLACKSTONEPRODUCTS.COM
OWNER’S MANUAL | OPERATION INSTRUCTIONS
LEAK TEST INSTRUCTIONS
• Leak test new and exchanged LPG cylinders BEFORE connecting to
appliance.
• DO NOT smoke during leak test.
• DO NOT use an open flame to check for gas leaks.
• Appliance must be leak tested outdoors in a well-ventilated
area, away from ignition sources such as gas fired or electrical
appliances.
• During leak test, keep appliance away from open flames or sparks.
LEAK TEST: VALVES, HOSE & REGULATOR
STEP 01
Turn the control knobs to OFF.
STEP 02
Connect the regulator to the LPG cylinder.
STEP 03
Completely open the LPG tank by turning the hand wheel
counterclockwise.
If you hear a rushing sound, turn gas o immediately. There is a major leak at
If you hear a rushing sound, turn gas o immediately. There is a major leak at
the connection.
STEP 04
Immediately close the LPG cylinder by turning the hand
wheel clockwise and re-tighten connections. If leaks cannot be
stopped DO NOT TRY TO REPAIR.
LEAK TEST: LPG CYLINDER
STEP 01
Use a clean paintbrush
to brush a mild soap and
water solution onto joint areas of
the LPG cylinder.
Leaks are indicated by growing
Leaks are indicated by growing
bubbles.
WARNING
If growing bubbles appear
during leak test, DO NOT use
or move the LPG cylinder.
Immediately contact an LPG
supplier or fire department.
STEP 05
Use a clean paintbrush
to brush a mild soap and
water solution onto joint areas of
valves and regulator.
Leaks are indicated by growing
Leaks are indicated by growing
bubbles.
STEP 06
Immediately close the
LPG cylinder by turning the
OPD hand wheel clockwise and
re-tighten connections.
WARNING
If leaks cannot be stopped, DO NOT try to repair.
Regulator must be replaced with a Blackstone approved
model by a professionally licensed, authorized dealer.
FITTINGS & HOSES
Prior to connection and use, ensure that there is no debris caught in,
or damage to, the head of the gas cylinder, regulator, hose, burner
and burner ports.
• Annual checking and tightening of metal fittings is recommended.
• Avoid twisting the flexible tube when the appliance is in use.
• Ensure that the hose is not obstructed, kinked, or in contact with
any part of the appliance other than at its connection.
• Before each use, check to see if hoses are cut or worn. (Worn or
damaged hose must be replaced before using appliance.)
(Use only Blackstone approved valve, hose, or regulator. Failure to comply will
(Use only Blackstone approved valve, hose, or regulator. Failure to comply will
void the warranty.)
• The LPG cylinder supply system must be arranged for vapor
withdrawal.
•
Always keep new LPG cylinders in upright position during use, transit or
Always keep new LPG cylinders in upright position during use, transit or
storage.
•
Always keep the ventilation opening(s) of the cylinder enclosure free and
Always keep the ventilation opening(s) of the cylinder enclosure free and
clear from debris.
If grease or other hot material drips onto valve, hose or regulator:
STEP 01
Turn o gas supply immediately.
STEP 02
Determine the cause and correct it.
STEP 03
Clean and inspect valve, hose and regulator.
STEP 04
Perform a leak test.
LPG CYLINDER REQUIREMENTS
FOR 20 LB (9 KG CYLINDERS)
• The LPG supply cylinder to be used must be constructed and
marked in accordance with the specifications for LP gas cylin-
ders, U.S. Department of Transportation (DOT) or the Standard for
Cylinders, Spheres and Tubes for the Transportation of Dangerous
Goods, CAN/CSA-B339.
• Only LPG cylinders marked “propane” shall be used.
THE LPG CYLINDER VALVE MUST HAVE:
• Type 1 valve outlet (thread on the outside).
• Safety relief valve.
• UL listed Overfill Protection Device (OPD). This OPD safety feature is
identified by a unique triangular hand wheel.
• Dust cap.
The seal on the valve outlet could, over time, show marked and visible damage
The seal on the valve outlet could, over time, show marked and visible damage
or deterioration that might cause a leak even with the connection tightened.
or deterioration that might cause a leak even with the connection tightened.
•
A visual inspection for the seal must be carried out every time a LPG
A visual inspection for the seal must be carried out every time a LPG
cylinder is replace or refilled.
cylinder is replace or refilled.
•
Any LPG cylinder showing signs of damage or deterioration as those illus-
Any LPG cylinder showing signs of damage or deterioration as those illus-
trated including visible cracks and pitting, must be returned unused to the
trated including visible cracks and pitting, must be returned unused to the
seller.
LPG cylinder valveLPG cylinder valve
Safety relief
Safety relief
valve
Hand wheel
Valve outlet
(check seal before use)
Dust cap
MODEL(S): 2311 • 2311CA
OPERATION INSTRUCTIONS
To Next Page