PLA88CS USER MANUAL
www.blustream.com.au | www.blustream-us.com | www.blustream.co.uk26
RS-232 Configuration and Telnet Commands
COMMAND ACTION
INxx CEC RIGHT RIGHT On Input xx
INxx CEC RETURN RETURN On Input xx
INxx CEC EXIT EXIT On Input xx
INxx CEC VOLUP VOLUME UP On Input xx
INxx CEC VOLDOWN VOLUME DOWN On Input xx
INxx CEC PLAY PLAY On Input xx
INxx CEC STOP STOP On Input xx
INxx CEC PAUSE PAUSE On Input xx
INxx CEC RECORD RECORD On Input xx
INxx CEC REWIND REWIND On Input xx
INxx CEC FF FAST FORWARD On Input xx
INxx CEC FWD FORWARD On Input xx
INxx CEC BWD BACKWARD On Input xx
INxx CEC POFF POWER OFF On Input xx
INxx CEC PON
POWER ON On Input xx
xx = 00: All Input Port
xx = [01-08]: Input 1 - 8
CECUSERCMD <u8
DevID u8Addr u8Opcode pu8Operand[MAX]>
u8DevID: 00 Select All CEC Input Port
u8DevID: [01-08] Input 1 - 8
u8DevID: F0 Select All CEC Output Port
u8DevID: [F1-F8] Output 1 - 8
pu8Operand[MAX] : MAX 0 - 14
Eg:CECUSERCMD <F0 40 44 41 > (ALL OUT CEC VOLUP)
Eg:CECUSERCMD <F0 40 44 42 > (ALL OUT CEC VOLDOWN)
RS232BAUD z
Set RS232 Baud Rate To xx
z = 1 2400, 2 4800, 3 9600, 4 19200, 5 38400, 6 57600
(Default), 7 115200
RS232SEND
xx:yy:z:a:b
Send b To RS232 Port xx And Wait yy Seconds For
Feedback
xx = 00 : Local RS232 Port
xx = [01-08] : Output 1 - 8
xx = [09-10] : Input 1 - 2
yy = [00-10] : Wait For The Feedback yy Seconds
z = a ASCII, h HEX
a = 1 2400, 2 4800, 3 9600, 4 19200, 5 38400, 6 57600
(Default), 7 115200
b = RS232 command
RS232DLYOUTxx:tt
Set Send Output xx Interval Time In tt Seconds Between
RS232 On And User Commands
xx = 00: All Output Port
xx = [01-08]: Output 1 - 8
tt = [0-180]: Delay tt Seconds
RS232DLYINxx:tt
Set Send Input xx Interval Time In tt Seconds Between
RS232 On And User Commands
xx = 00: All Input Port
xx = [01-02]: Input 1 - 2
tt = [0-180]: Delay tt Seconds
RS232OUTxx ON Enable RS232 Remote-control Mode On HDBT Out xx
RS232OUTxx OFF
Disable RS232 Remote-control Mode On HDBT Out xx
xx = 00: All HDBT Output Port
xx = [01-08]: HDBT Output 1 - 8
RS232INxx ON Enable RS232 Remote-control Mode On HDBT In xx
COMMAND ACTION
RS232INxx OFF
Disable RS232 Remote-control Mode On HDBT In xx
xx = 00: All HDBT Input Port
xx = [01-02]: HDBT Input 1 - 2
RS232ONOUTxx
y:z:a:b
Save y Type Of Command a Stored In Slot x Whose Baud
Rate Is z On Input xx
xx = 00: All Output Port
xx = [01-08]: Output 1 - 8
y = 1 RS232 Display On
y = 2 RS232 Display Input Select
y = 3 RS232 User Command 1
y = 4 RS232 User Command 2
y = 5 RS232 User Command 3
z = a ASCII, h HEX
a = 1 2400, 2 4800, 3 9600, 4 19200, 5 38400, 6 57600
(Default), 7 115200
b = RS232 Command
RS232ONINxx
y:z:a:b
Save y Type Of Command a Stored In Slot x Whose Baud
Rate Is z On Input xx
xx = 00: All Output Port
xx = [01-08]: Output 1 - 8
y = 1 RS232 Display On
y = 2 RS232 Display Input Select
y = 3 RS232 User Command 1
y = 4 RS232 User Command 2
y = 5 RS232 User Command 3
z = a ASCII, h HEX
a = 1 2400, 2 4800, 3 9600, 4 19200, 5 38400, 6 57600
(Default), 7 115200
b = RS232 Command
RS232OFFOUTxx
y:z:a:b
Save RS232 O Command a Of y Type Whose Baud Rate
Is z On Output xx
y = 1 RS232 Display O 1
y = 2 RS232 Display O 2
z = a ASCII, h HEX
a = 1 2400, 2 4800, 3 9600, 4 19200, 5 38400, 6 57600
(Default), 7 115200
b = RS232 Command
RS232OFFINxx
y:z:a:b
Save RS232 O Command a Of y Type Whose Baud Rate
Is z On Output xx
y = 1 RS232 Display O 1
y = 2 RS232 Display O 2
z = a ASCII, h HEX
a = 1 2400, 2 4800, 3 9600, 4 19200, 5 38400, 6 57600
(Default), 7 115200
b = RS232 Command
RS232ONOUTxx
DISABLE Disable Auto RS232 Commands When
Detecting A Signal On Output xx
RS232OFFOUTxx
DISABLE Disable Auto RS232 Commands When Not
Detecting A Signal On Output xx
xx = 00: All Output Port
xx = [01-08]: Output 1 - 8
NET DHCP ON/OFF Set Auto IP(DHCP) On Or O
NET TN ON/OFF Set Telnet Port On Or O
NET TN8000 ON/OFF Set Telnet Port 8000 On Or O
NET IP xxx.xxx.xxx.xxx Set IP Address
NET GW xxx.xxx.xxx.xxx Set Gateway Address
NET SM xxx.xxx.xxx.xxx Set Subnet Mask Address
NET RB Set Network Reboot And Apply New Config!!!
NET TN xxxx Set Telnet Port
To Next Page
Loading...
