Bomar 320.258 DG - Page 4

7
3.
3.3.6. Speed adjustment of the arm lowering ...................................................................... 54
3.3.7. Setting the type of cooling ............................................................................................ 55
3.4. Material insertion............................................................................................................................. 55
3.4.1. Selecting means of manipulation ................................................................................. 55
3.4.2. Insertion ............................................................................................................................. 55
3.4.3. Bundle material cutting .................................................................................................. 55
4. ÚDRŽBA STROJE / MACHINE MAINTENANCE / WARTUNG .. 58
4.1. Saw band dismantling .................................................................................................................... 60
4.2. Saw band installation ..................................................................................................................... 62
4.3. Saw band stretching and inspection ........................................................................................... 64
4.3.1. Saw band stretching ........................................................................................................ 65
4.3.2. Saw band inspection ....................................................................................................... 65
4.4. Adjustment ....................................................................................................................................... 67
4.4.1. Saw band run adjustment .............................................................................................. 67
4.4.2. Hard metal guides adjustment on the machine ....................................................... 67
4.4.3. Guide cube adjustment .................................................................................................. 69
4.4.4. Brush adjustment ............................................................................................................. 69
4.4.5. Adjusting the limit switch of the saw band stretching .............................................. 71
4.4.6. Saw frame lower position stop adjustment................................................................ 72
4.4.7. Adjustment of the limit switch of saw frame lower stop ......................................... 72
4.5. Cooling agents and chip disposal ............................................................................................... 73
4.5.1. Coolant inspection ........................................................................................................... 73
4.5.2. Cooling liquid preparation ............................................................................................. 75
4.5.3. Chips disposal ................................................................................................................... 75
4.6. Gearbox oils and greases .............................................................................................................. 77
4.6.1. Gearbox oils ...................................................................................................................... 77
4.6.2. Lubrication greases ......................................................................................................... 78
4.6.3. Lubrication ......................................................................................................................... 78
4.6.4. Hydraulic oils ..................................................................................................................... 79
4.7. Machine cleaning ............................................................................................................................ 79
4.8. Worn pieces replacement ............................................................................................................. 80
4.8.1. Hard metal guides replacement ................................................................................... 80
4.8.2. Saw band guiding rollers replacement ........................................................................ 81
4.8.3. Worn brush replacement ............................................................................................... 82
4.8.4. Stretching wheel replacement ...................................................................................... 84
4.8.5. Driving wheel replacement ............................................................................................ 86
4.8.6. Cooling pump replacement .......................................................................................... 87
5. ZÁVADY / TROUBLESHOOTING / STÖRUNGEN ................... 90
5.1. Mechanical problems ..................................................................................................................... 92
5.2. Electrical problems .......................................................................................................................... 94
5.2.1. Hydraulic problems ......................................................................................................... 95
6. SCHÉMATA / SCHEMATA / SCHEMATICS ............................. 98
6.1. Elektrická schémata / Elektroschemas / Wiring diagrams 3x400 V + PE, 50Hz ............. 100
6.2. Elektrické schéma /Elektroschema /Wiring diagrams – 3x230 V + PE, 50H ................... 112
6.3. Hydraulické schema / Hydraulisches Schéma / Hydraulic diagram ................................... 125
7. VÝKRESY SESTAV PRO OBJEDNÁNÍ NÁHRADNÍCH DÍLŮ /
ZEICHNUNGEN FÜR BESTELLUNG DER ERSATZTEILE / DRAWING
ASSEMBLIES FOR SPARE PARTS ORDER ..................................... 128
7.1. Ergonomic 320.258 DG ................................................................................................................ 130
7.2. Kusovník / Piece list / Stückliste - Ergonomic 320.258 DG ................................................... 131
7.3. Ergonomic 320.258 DG ................................................................................................................ 132
7.4. Kusovník / Piece list / Stückliste - Ergonomic 320.258 DG ................................................... 133
7.5. Chlazení / Cooling / Kühlung ...................................................................................................... 134
7.6. Kusovník / Piece list / Stückliste - Chlazení / Cooling / Kühlung ........................................ 135
7.7. Podstavec / Base / Untersatz ...................................................................................................... 136
7.8. Kusovník / Piece list / Stückliste - Podstavec / Base / Untersatz ......................................... 137
7.9. Vana/ Tank/ Wanne ...................................................................................................................... 138
7.10. Kusovník / Piece list / Stückliste - Vana/ Tank/ Wanne ............................................... 139