EasyManua.ls Logo

Bomar Ergonomic 320.250 GH - User Manual

Bomar Ergonomic 320.250 GH
107 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Series Ergonomic
Ergonomic 320.250 GH
Operating instructions
Before transporting and using the machine,
please read the instructions thoroughly!
Seriové číslo / Serien Nummer / Serial Number ___________________

Table of Contents

Questions and Answers

  • E
    Elizabeth HartAug 9, 2025
    What to do if the Bomar Saw cut is not at the desired angle?
    • J
      Jodi BairdAug 9, 2025
      If your Bomar Saw cut isn't at the desired angle, it could be due to: * A loosened securing lever. * A set angle that doesn't match the cut angle. * Insufficient saw band stretching. * Loosened guiding arm and guiding cube. * Dirt between the material and clamping jaw. Check and tighten the securing lever and guiding arm, ensure the angle adjustment is accurate, stretch the saw band properly, and clean any dirt from the material and clamping jaw.
  • D
    Daniel RussellAug 19, 2025
    How to extend the saw band lifetime on my Bomar Saw?
    • C
      Clayton AndersonAug 20, 2025
      A short saw band lifetime on your Bomar Saw can result from: * Insufficient saw band stretching. * A worn or wrongly adjusted swarf brush. * An over stretched saw band. * Wrongly adjusted or worn hard metal guides of the saw band. To extend the saw band's life, ensure proper saw band stretching, check and replace the swarf brush if worn, avoid over stretching the saw band, and verify the hard metal guides are correctly adjusted and not worn.
  • R
    rubiorobertOct 28, 2025
    Why is my Bomar Saw cutting at a slant?
    • N
      Nicole OliverOct 29, 2025
      A slanting cut on your Bomar Saw can occur due to several reasons: * Hard metal guides might be wrongly adjusted or worn. * Cubes of the saw band guiding could be wrongly adjusted. * Bearings of the saw band guiding might be worn. * The swarf brush could be wrongly adjusted or worn. * The saw band might not be stretched enough or is worn. * The tooth system of the saw band might be wrongly chosen. * The roller conveyor is wrongly balanced, or the feeding board is dirty. * The guiding arm and guiding cube are loosened or too far from the material. * The cutting rate is too fast, or there's unexpected oscillation in material quality. To resolve this, ensure all components are correctly adjusted, clean, and in good condition. Also, adjust cutting speed and saw band tensio...

Summary

Safety Notes

Machine Determination

Defines the intended use of the Ergonomic 320.250 GH band saw for cutting various materials.

Protective Suit and Personal Safety

Details essential personal protective equipment (PPE) and safety practices for machine operators.

Safety Notes for Machine Operator

Provides critical safety guidelines and responsibilities for the machine operator.

Safety Notes for Servicing and Repairs

Outlines safety precautions to be followed during maintenance and repair activities.

Safety Notes for Hydraulic Unit Servicing and Repairs

Safety Machine Accessories

Machine Documentation

Technical Data

Presents detailed technical specifications, dimensions, and electrical/hydraulic parameters of the machine.

Installation Diagram

Description

Transportation and Stocking

Band Saw Unpacking and Assembling

Guides users through the process of unpacking and assembling the band saw.

Electrical Connection

Explains the procedures and safety requirements for connecting the machine to the electrical supply.

Filling of the Cooling System

Check Machine Function

Saw Band

Machine Control

Main Switch

Control Panel

Details the operation and components of the machine's control panel.

Cutting

Explains the process and steps involved in performing cutting operations.

Cycle Breaking

Band Saw Adjusting

Covers various adjustments for the band saw, including speed, pressure, and angles.

Material Insertion

Machine Service

Saw Band Dismantling and Installation

Detailed steps for removing and installing the saw band.

Saw Band Stretching and Inspection

Guides on properly stretching and inspecting the saw band for optimal performance.

Saw Band Run Adjustment on Stretching Wheel

Explains how to adjust the saw band's tracking on the stretching wheel.

Saw Band Adjusting

Covers adjustments for guides, limit switches, and pressure for saw band performance.

Cooling Agents and Chips Disposal

Hydraulic, Greases and Oils

Worn Pieces Replacement

Instructions for replacing worn parts like guides, rollers, brushes, and wheels.

Troubleshooting

Mechanical Problems

Lists common mechanical issues and their potential causes and repair solutions.

Electric Problems

Addresses electrical malfunctions, their causes, and recommended repair steps.

Hydraulic Problems

Details common hydraulic issues, their causes, and troubleshooting guidance.

Bomar Ergonomic 320.250 GH Specifications

General IconGeneral
BrandBomar
ModelErgonomic 320.250 GH
CategorySaw
LanguageEnglish

Related product manuals