Bomar Ergonomic 320.250 DGSH

Questions and Answers

K
Keith VillarrealJul 29, 2025
Why is my Bomar Ergonomic 320.250 DGSH Saw cutting at a slant?
- A
  Anna DavidsonJul 30, 2025
  If your Bomar Saw is producing slanted cuts, there are several potential causes. It could be due to wrongly adjusted or worn hard metal guides, or wrongly adjusted cubes of the saw band guiding. Other possible causes include worn bearings of the saw band guiding, a wrongly adjusted or worn swarf brush, insufficient saw band stretching, or a wrongly chosen tooth system for the saw band. A worn saw band, wrongly balanced roller conveyor, or a dirty feeding board could also be contributing factors. Additionally, check if the guiding arm and guiding cube are loosened or too far from the material. Finally, consider whether the cutting rate is too fast or if there are unexpected oscillations in material quality, and adjust accordingly.
N
Natalie TorresAug 8, 2025
What to do if the cut angle is wrong on my Bomar Ergonomic 320.250 DGSH?
- J
  Jordan SmithAug 8, 2025
  If the cut angle on your Bomar Saw doesn't match the set angle, the securing lever might be loosened. Ensure it's properly adjusted. The set angle might not match the actual cut angle, so verify with a protractor. Insufficient saw band stretching can also cause this, so ensure proper tension. Check that the guiding arm and guiding cube are fastened securely. Finally, dirt between the material and clamping jaw can interfere, so clean both surfaces.
R
Rachel GarciaAug 18, 2025
Why does the saw band have a short lifetime on my Bomar Ergonomic 320.250 DGSH?
- E
  Erika Howell MDAug 18, 2025
  A short lifetime of the saw band on your Bomar Saw could be caused by several factors. Insufficient or over stretched saw band. A worn or wrongly adjusted swarf brush can also contribute to premature wear. Additionally, check for wrongly adjusted or worn hard metal guides of the saw band.

Summary

Safety Notes

Personal Protective Equipment

Details essential safety gear for operators to prevent injuries.

Operator Safety Guidelines

Outlines rules for safe machine operation by the user.

Servicing and Repair Safety

Provides safety guidelines for maintenance and repair activities.

Hydraulic Unit Safety Precautions

Specific safety precautions for the hydraulic system.

Machine Accessories Safety

Safety Symbols and Placement

Machine Documentation

Technical Data and Specifications

Lists key technical specifications and dimensions of the machine.

Installation Diagram

Transportation and Stocking Procedures

Band Saw Unpacking and Assembly

Electrical Connection Guide

Procedures for connecting the machine to the electrical power supply.

Machine Function Checks

Saw Band Information

Machine Control

Control Panel Overview

Identifies and explains the machine's control buttons and indicators.

Cutting Operations Procedure

Step-by-step guide for performing cutting tasks.

Cutting Pressure Adjustment

Material Insertion and Handling

Machine Service and Maintenance

Saw Band Dismantling

Saw Band Installation

Saw Band Stretching and Inspection

Component Adjustments

Detailed instructions for adjusting various machine components.

Coolant and Chip Disposal

Lubricants and Oils Recommendations

Worn Parts Replacement Guide

Guides for replacing worn components like guides and rollers.

Troubleshooting

Mechanical Problems and Solutions

Identifies common mechanical issues and their solutions.

Electrical Problems and Solutions

Lists electrical faults and troubleshooting steps.

Hydraulic Problems and Solutions

Addresses issues related to the hydraulic system and their remedies.

Schematics and Diagrams

Wiring Diagrams (No Frequency Converter)

Wiring Diagrams (With Frequency Converter)

Hydraulic System Diagrams

Bomar Ergonomic 320.250 DGSH Specifications

General

Cutting capacity at 90 degrees (round)	320 mm
Cutting capacity at 90 degrees (square)	250 mm
Cutting capacity at 90 degrees (rectangle)	320 x 250 mm
Motor power	1.5 kW
Category	Saw
Type	Semi-automatic