Bosch AQT 42-13

Questions and Answers:

I
ianmccarthySep 2, 2025
Why is the pressure pulsating on my Bosch AQT 42-13 Pressure Washer and how to fix it?
- S
  shelbybarrettSep 2, 2025
  If your Bosch Pressure Washer experiences pressure pulsation, it could be due to several reasons: * There might be air in the inlet water supply hose or pump. To resolve this, run the pressure washer with the spray handle open and the nozzle at low pressure until regular working pressure is achieved. * The water supply may be inadequate. Ensure it meets the specifications, with a minimum hose diameter of 1/2" or 13 mm. * The water filter could be blocked, requiring cleaning. * Check for and straighten any kinks in the water supply hoses. * If using a high-pressure extension hose, remove it and retry, ensuring it doesn't exceed the maximum length of 7 m.
J
John MartinezAug 31, 2025
Why does my Bosch Pressure Washer motor keep stopping?
- A
  Anthony HillAug 31, 2025
  If your Bosch Pressure Washer motor stops, check the fuse and replace it if faulty. Ensure the mains voltage corresponds to the specifications on the model tag. Also, the motor protector may have activated; in this case, allow the unit to cool for 15 minutes.
S
Samuel BuckleyAug 29, 2025
Why is water leaking from my Bosch Pressure Washer?
- L
  Larry WareAug 29, 2025
  A slight water leak from your Bosch Pressure Washer is permissible. However, if the leak is excessive, contact a service center.
K
Kenneth WilliamsAug 27, 2025
Why does my Bosch Pressure Washer motor sound like it's starting but won't actually start?
- T
  Thomas TaylorAug 28, 2025
  If your Bosch Pressure Washer motor “sounds” but fails to start, check the following: * Ensure that the voltage of the mains power supply line is the same as that on the plate, as insufficient power supply can cause this issue. * If you're using an extension cable, voltage loss might be the problem. Check the characteristics of the extension cable.
M
matthew77Aug 26, 2025
How to fix a Bosch AQT 42-13 Pressure Washer when the motor refuses to start?
- A
  amymortonAug 27, 2025
  If your Bosch Pressure Washer motor refuses to start, there are several potential causes: * Ensure the plug is properly connected. * Try a different mains socket to rule out a faulty socket. * Check and replace the fuse if it's faulty or blown. * Remove any extension cables to see if they are the issue. * Allow the motor to cool for 15 minutes if the motor protector has activated. * Ensure that pump/water supply hose/accessory is not frozen.
N
nguyenjasonAug 25, 2025
What to do if Bosch AQT 42-13 motor starts but there is no pressure?
- A
  Amy BushAug 25, 2025
  If your Bosch Pressure Washer motor starts but there's no pressure, the nozzle might be partly blocked. Try cleaning the nozzle.
A
Adam HensonAug 22, 2025
Why does my Bosch AQT 42-13 Pressure Washer motor start but have no pressure?
- B
  Brenda ColeAug 22, 2025
  If your Bosch Pressure Washer motor starts up but provides restricted or no working pressure, consider the following: * Ensure that the water supply is connected. * Clean the water filter if it's clogged. * Clean the nozzle if it's clogged.

Bosch AQT 42-13 Specifications

General

Form factor	Compact
Hose length	7 m
Cable length	5 m
Power source	Electric
Product color	Black, Green, Red
Detergent reservoir	-
Maximum flow rate	420 l/h
Minimum flow rate	- l/h
Working pressure (max)	130 bar
Working pressure (min)	- bar
Maximum input water temperature	40 °C
Power consumption (typical)	1900 W