To Next Page
H
holly32Aug 14, 2025
Why is there no video on my Bosch Security Camera?
- Ddenise79Aug 14, 2025
If your Bosch Security Camera displays no video, ensure that the device is properly powered and that all cables are securely connected.
Why is there no video on my Bosch Security Camera?
If your Bosch Security Camera displays no video, ensure that the device is properly powered and that all cables are securely connected.
What to do if colors are not correct on Bosch Security Camera?
If the colors on your Bosch Security Camera appear incorrect, try resetting the camera to its factory default settings using the command (ON-40-ENTER). You can also try positioning the camera so its entire view is white, like a piece of paper or a white wall. Another solution is to turn on White Balance (OFF-30-ENTER), move the joystick until one shot is selected, wait 2 seconds, and then press IRIS to return. If none of these steps work, restore factory defaults using (SET-899-ENTER). Note that this will erase all presets and settings. Once you have restored the proper settings, it is recommended to store those settings in Preset #1 (SET-1-ENTER) so they are recalled each time the Preset is called.
How to fix picture dark on Bosch Security Camera?
If the picture on your Bosch Security Camera is dark, ensure that the Gain Control is activated by using the command (ON-43-ENTER). Also, verify that the Iris level hasn't been inadvertently altered. If it has, adjust it using the IRIS control on the keyboard. To permanently adjust, use the command ON-11-ENTER.
What to do if I cannot access user settings on my Bosch Security Camera?
If you are unable to access the user settings on your Bosch Security Camera, unlock the commands by entering (OFF-90-ENTER). Please note that the commands will automatically lock 30 minutes after being unlocked.
Why is the background too bright on my Bosch Security Camera?
If the background is too bright and obscures the subject on your Bosch Security Camera, turn on Backlight Compensation using the command (ON-20-ENTER). Note that Backlight Compensation will turn off with any camera movement.
Why is my Bosch Security Camera picture rolling, noisy, or distorted?
If the picture from your Bosch Security Camera is rolling, noisy, or distorted, it may be due to electronic AC power line noise interfering with the sync. If the picture is distorted, try switching to Internal Crystal by using the command (OFF-42-ENTER). If this corrects the picture problems, there may be excessive line noise on the power supply.
What to do if I have no control of my Bosch Security Camera?
If you have no control over your Bosch Security Camera, ensure that the address is set correctly. Also, verify that the biphase or RS-232 is properly connected. Check if other cameras can be controlled; if not, investigate the control system.
Why does my Bosch Security Camera move when moving other cameras?
If your Bosch Security Camera moves when you are moving other cameras, ensure that the address is set properly. If the FastAddress is not set, the camera will respond to commands for any address.
Why do I experience periodic loss of control with my Bosch Security Camera?
If you experience a periodic loss of control with your Bosch Security Camera, verify that a 110 ohm resistor is across the +/- biphase code terminals at the last dome being controlled.
Instructions on how to safely disconnect power to the unit.
Warnings and procedures for removing the unit's cover safely.
Safety guidelines for units operating with 24 VAC power input.
Requirements for using 220-240V, 50Hz power cords.
Detailed steps for installing pendant housings and mounts.
Instructions for wiring the control connector on pendant housings.
Steps to attach the pendant housing to the mounting hardware.
Guide for inserting the camera module into the housing correctly.
Configuration options for camera functions like white balance, gain, sharpness.
Settings related to camera lens functions like focus, iris, and zoom.
Configuration for Pan, Tilt, and Zoom (PTZ) movements and tours.
Options for on-screen display elements and video output.
Settings for device communication protocols and baud rates.
Selection of the user interface language for the device.
How to save camera positions and settings as presets.
Instructions on creating and managing camera preset tours.
Adjusting the dwell time between presets in a tour.
How to record and playback camera movements and commands.
Adjusting the speed for automatic pan and scan functions.
General| Brand | Bosch |
|---|---|
| Model | BasicDome Series |
| Category | Security Camera |
| Language | English |
