14 | English
Assembly
u Avoid starting the power tool unintentionally. The
mains plug must not be connected to the power supply
during assembly or when carrying out any kind of
work on the power tool.
Items included
See the list of items included at the start of
the operating manual.
Check to ensure that all the parts listed below have been
supplied before using the power tool for the first time:
– Mitre saw with mounted saw blade
– Dust bag (19)
– Screw clamp (18)
– Hex key/cross-headed screwdriver(22)
– Tilt protector(24) with fastening set(35) (2 bolts, 2
washers, 2 square nuts)
Note: Check the power tool for possible damage.
Before continuing to use the power tool, carefully check that
all protective devices or slightly damaged parts are working
perfectly and according to specifications. Check that the
moving parts are working perfectly and without jamming;
check whether any parts are damaged. All parts must be fit-
ted correctly and all the conditions necessary to ensure
smooth operation must be met.
If the protective devices or any parts become damaged, you
must have them properly repaired or replaced by an author-
ised service centre.
Fitting individual components
– Carefully remove all parts included in the delivery from
their packaging.
– Remove all packing material from the power tool and the
accessories provided.
Mounting the tilt protector (see figure A)
Before the power tool is used for the first time, the tilt pro-
tector(24) must be installed.
Use the "tilt protector" fastening set(35) for the installation.
– Insert the square nuts(35) into the corresponding
holes(34) in the base plate.
– Place the washers(35) on the fastening screws(35) and
use them to screw the tilt protector(24) into the inserted
nuts.
u Do not remove the tilt protector. Without the tilt pro-
tector, the power tool will not be stable and can tip over
especially when sawing maximum mitre/bevel angles.
Fitting the extension bar (see figure B)
The free end of long and heavy workpieces must have some-
thing placed underneath it or be supported.
To extend the saw table further, extension bars can be
mounted both to the left or right of the power tool.
– Push the extension bars(36) on both sides of the power
tool all the way into the corresponding drill holes(16).
– Tighten the fastening screws(37) to secure the extension
bars.
Stationary or flexible mounting
u To ensure safe handling, the power tool must be
mounted on a flat, stable work surface (e.g. work
bench) before use.
Mounting on a work surface (see figure C1−C2)
– Use suitable screw fasteners to secure the power tool to
the work surface. The holes (14) are used for this pur-
pose.
or
– Firmly clamp the base of the power tool to the work sur-
face with commercially available screw clamps.
Mounting on a Bosch saw stand
With the height-adjustable legs, Bosch GTA saw stands
provide firm support for the power tool on any surface. The
workpiece supports of the saw stand are used for underlay-
ing long workpieces.
u Read all the warnings and instructions included with
the saw stand. Failure to observe the warnings and fol-
low instructions may result in electric shock, fire and/or
serious injury.
u Assemble the saw stand properly before mounting the
power tool. Correct assembly is important to prevent the
risk of collapsing.
– Mount the power tool on the saw stand in the transport
position.
Dust/Chip Extraction
The dust from materials such as lead paint, some types of
wood, minerals and metal can be harmful to human health.
Touching or breathing in this dust can trigger allergic reac-
tions and/or cause respiratory illnesses in the user or in
people in the near vicinity.
Certain dusts, such as oak or beech dust, are classified as
carcinogenic, especially in conjunction with wood treatment
additives (chromate, wood preservative). Materials contain-
ing asbestos may only be machined by specialists.
– Use a dust extraction system that is suitable for the ma-
terial wherever possible.
– Provide good ventilation at the workplace.
– It is advisable to wear a P2 filter class breathing mask.
The regulations on the material being machined that apply in
the country of use must be observed.
u Avoid dust accumulation at the workplace. Dust can
easily ignite.
The dust/chip extraction system can be blocked by dust,
chips or fragments of the workpiece.
– Switch the power tool off and pull the mains plug out of
the socket.
– Wait until the saw blade has come to a complete stop.
– Determine the cause of the blockage and eliminate it.
1 609 92A 4YM | (15.05.2019) Bosch Power Tools
To Next Page
Loading...
