Bosch GCM 10 MX - 5.7.2.1 Checking (see figure P1); 5.7.2.2 Setting (see figure P2); 5.7.3 Setting the standard 45° bevel angle; 5.7.3.1 Checking (see figure Q1)

18 | English
– Turn the saw table (7) to the 0° detent (45). The lever
(11) must be felt to engage in the detent.
Checking (see figure P1)
– Set an angle gauge to 90° and place it on the saw table
(7).
The leg of the angle gauge must be flush with the saw blade
(41) along its entire length.
Setting (see figure P2)
– Loosen the clamping handle (26).
– Loosen the lock nut of the stop screw (33) using a com-
mercially available ring spanner or open-ended spanner
(13mm).
– Turn the stop screw as far in or out as needed until the leg
of the angle gauge is flush with the saw blade along its en-
tire length.
– Retighten the clamping handle (26).
– Then retighten the lock nut of the stop screw (33).
If the angle indicator (31) is not aligned with the 0° mark on
the scale (32) following adjustment, loosen the screw (48)
using a commercially available cross-headed screwdriver
and align the angle indicator along the 0° mark. (See figure
R)
Setting the standard 45° bevel angle
– Bring the power tool into the work position.
– Turn the saw table (7) to the 0° detent (45). The lever
(11) must be felt to engage in the detent.
– Loosen the clamping handle (26) and use the handle (3)
to swivel the tool arm all the way to the left (45°).
Checking (see figure Q1)
– Set an angle gauge to 45° and place it on the saw table
(7).
The leg of the angle gauge must be flush with the saw blade
(41) along its entire length.
Setting (see figure Q2)
– Loosen the lock nut of the stop screw (23) using a com-
mercially available ring spanner or open-ended spanner
(13mm).
– Turn the stop screw as far in or out as needed until the leg
of the angle gauge is flush with the saw blade along its en-
tire length.
– Retighten the clamping handle (26).
– Then retighten the lock nut of the stop screw (23).
If the angle indicator (31) is not aligned with the 45° mark on
the scale (32) following adjustment, first check the 0° set-
ting for the bevel angle and the angle indicator once more.
Then repeat the adjustment of the 45° bevel angle.
Transport (see figure S)
Before transporting the power tool, the following steps must
be carried out:
– Bring the power tool into the transport position.
– Remove all accessories that cannot be securely fitted to
the power tool.
If possible, transport unused saw blades in a closed con-
tainer.
– Carry the power tool by the transport handle (28) or hold
it by the recessed handles(15) on the sides of the saw
table.
u Only use the transport devices to transport the power
tool and never the protective devices.
Maintenance and servicing
Maintenance and cleaning
u Pull the plug out of the socket before carrying out any
work on the power tool.
u To ensure safe and efficient operation, always keep
the power tool and the ventilation slots clean.
In order to avoid safety hazards, if the power supply cord
needs to be replaced, this must be done by Bosch or by an
after-sales service centre that is authorised to repair Bosch
power tools.
The retracting blade guard must always be able to move
freely and retract automatically. It is therefore important to
keep the area around the retracting blade guard clean at all
times.
Always remove dust and chips after working by blowing out
with compressed air or using a brush.
Accessories
Article number
3601M29040, 3601M290B0:
Extension bar
1 619 PA6 916
Saw blades for hardwood, composites, plastic and non-
ferrous metals
254 x 25.4 mm saw blade, 100 teeth 1 609 B00 844
Saw blades for wood and fibreboard, panels and strips
254 x 25.4 mm saw blade, 40 teeth 2 608 673 047
254 x 25.4 mm saw blade, 100 teeth 2 608 640 904
After-Sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on
spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you
with any questions about our products and their accessor-
ies.
In all correspondence and spare parts orders, please always
include the 10‑digit article number given on the nameplate
of the product.
Cambodia
Robert Bosch (Cambodia) Co., Ltd
Unit 8BC, GT Tower, 08th Floor, Street 169,
Czechoslovakia Blvd, Sangkat Veal Vong
Khan 7 Makara, Phnom Penh
VAT TIN: 100 169 511
Tel.: +855 23 900 685
1 609 92A 4YM | (15.05.2019) Bosch Power Tools