Bosch HPC 400 User Manual

Getting started
~ Press the menu key to open the main menu .
~ Press the selector to open the HeatingfCooling menu .
~ Press the selector to open the Operating mode menu .
I
~~ If two or more heating circuits are installed. turn the selector to highlight Heating
circuit 1. 2. 3 or 4 and press the selector .
Turn the selector to highlight Optimise and press the selector.
I
~ Press and hold the Back key to return to the standard display . I
The required room temperature is shown in a pop : up window in the lower part of the
display. The user interface will now constantly maintain the required room
temperature .
Table 5 Getting started - Activating operating modes
4.3 Changing the room temperature
Fr, 21 ,03.201.
Lto .S OC
Flow temperat ur e
He1 Optimise
BOSCH
12:35
10
12 .5 'C
6720812n~ . 10
Operating the appliance Result
If it is too cold or too warm for you today: a..n.. .... .-.......... . , . _
Changing the room temperature until th e next switching time
~ Turn the selector to set the required room temperature .
The corresponding time slot is displayed in grey in the time program bar chart .
~ Wait a few seconds or press the selector.
The user interface operates with the modified setting . The change applies until
the next switching time in your heating system time program is reached . After
i this. the time program settings are restored.
I
E I Undoing a temperature change
i ~ Turn the selector until the corresponding time slot turns back to black in the time
o program bar chart and press the selector .
~ The change is undone .
Fr,21.03.20'4
12 :35
Lto .S OC
10
12 .5 'c
~ow temperature
He3 Pro •. ,
·0 0 C!l 1ll':"
6 720 812 n5-()S . 10
Should it be permanently too cold or too hot for you: ................ II., .... ___ ~~ ___ ---!
~ Activate optimised operation (~ Chapter 4. 2) .
~ Wait a few seconds or press the selector to close the pop · up window .
~ Turn the selector to set the required room temperature .
~ Wait a few seconds or press the selector . Press the selector to confirm the change
in the pop·up window (or press the back key to discard the change) .
Table 6
The room temperature that is currently valid is shown in a pop·up window in the
lower part of the display .
The user interface operates with the modified settings.
Getting started - Room temperature
Fr, 21.03 201.
HCC(Heltlnr clreutt 4)
Chana' room temp . ror optimised
heat pump
optratlon to lO.O·C7
12:35
6720 812 n5-OO. 10
10 HPC400-6720821983(2017/07)
BOSCH
Getting started
Operating the appliance Result
~ Press the menu key to open the main menu .
~ Press the selector to open the H ea tingf Cool i ng menu .
~ Turn the selector to highlight the Te mperature se tt in gs menu . I
~ Press the selector to open the menu .
~ If two or more heating circuits are installed. turn the selector to highlight Heat i ng
ci rcuit 1. 2. 3 or 4 and press the se l ector .
~I
I
~ Turn the selector to highlight He ating. Se tback or Cool ing. -----f
... Press the selector .
~ Turn the selector and press it to activate the required setting. e.g. for setlback
mode . .
~ Turn and press the selector to set the temperature . The limits ofthe setting values I
1 for the temperatures are determined by the settings forlhe other operating mode
· in each case .
1 The user interface operates with tlhe modified settings . The settings are applied
~ to all time programs for the heating system (if two or more heating circuits are
c installed. it is only applied in the selected heating circuit) .
Table 6 Getting started - Room temperature
4.4 More settings
m II til Ir 1111 I
I Heating 21.0'C
Setback
I 15.0'C
Cooling
I 19.0'C
6720 811 136-07. 10
o Heitlngoff
, • • 'C 50 -= 20 .5
Ent.rthe setback temperature
6 720 811 1:MHl8. 10
Operating the appliance Result
If you need hot water outside of the times set If! the time program: AcIIRIt-. .... (. immecrllte DHW function).
~ Press the extra DHW key .
DHW heating is active immediately with the set temperature and for the set duration .
After a few seconds. the symbol for extra DHW will be displayed in the information
graphic ( Extr a ho t water settings ~ Chapter 5.3.3. page 22).
To deact i vate the extra DHW function before the end of the set duration :
~ Press the extra DHW key again .
If the DHW is too cold or too hot for you: a-.. ........................
~ Press the DHW key .
The user interface will display a list of the DHW heating operating modes (for more
information ~ Chapter 5.3.1. page 21).
~ Turn the selector to highlight the required operating mode .
I
~ Press the selector.
The user interface operates with the modified settings . Your contractor can set the
temperatures for the DHW and DHW reduced operating modes .
If optimised mode is active. the temperature will not be changed .
Table 7 Getting started - More settings
Fr,21.D3.2D1.
Lto.S OC
Fl ow temperatUf1
He1 OPtlml,.
12~35
10
12 .5"
6720812nlHl9 . 10
o ~Iways on • OHW red. I
o Always on . DHW
Ir l·~~~n~tl~me~p~ro~w~~------~I
S,~ct operatlnr mode ror
DHWsystem.
6720811 136-10. 10
HPC 400 - 6720821983 (2017/07) 11

Bosch HPC 400 Specifications

General

Brand	Bosch
Model	HPC 400
Category	Control Panel
Language	English