Bosch HPC 400 User Manual

Overview of control elements and symbols
@ BOSCH
-7 Fig . 2. page 7
Item Symbol Designation Explanation
6
Information
Information graphics are displayed in this section . These provide information
graphic
about what is currently active in the system .
...
DHW heating active
~
•
Thermal disinfection (DHW) active
mjjjj'l
f---
·
Extra DHW active
+"'"
·
Swimming pool is being heated
;;:"I
-
-
1D.
Heating active
•
Cooling active
-- -
+.
Interruption by energy supplier
-
(Co»
External switching contact closed (remote)
0
Holiday function active
<9
Time program · program lor 2 for heating active
.0-
Function for smart grid activated
?U
Screed drying active
-
+.
Electric booster heater active
+-
P;;;r guard active
[J9
Additional device (auxiliary heater) active
f
Defrost function active
~ -
Heat pump running
-
-::--:- .
.-
~
Solar pump running
7
Optimise Mode
Program 1
The heating system follows the active time program for the corresponding heating
Program 2
circuit. The heating system switches between heating mode and setback mode at
the times set.
~
--
Heating mode in the displayed heating circuit active
({
I Setback mode in the displayed heating circuit active
Table 3 Symbols on the standard display
8 HPC 400- 6 720821983 (2017/07)
BOSCH
Getting started
4
Getting started
4.1 Selecting a heating circuit for the standard
display
An overview of the structure of the main menu and the position
of the individual menu items can be found on page 14 .
Each of the following descriptions takes the standard display as
its starting pOint (-7 page 2. Fig . 7 atieft).
The standard display only ever shows data for a single heating
circuit. If two or more heating circuits are installed . a setting
can be made to determine which heating circuit the data in the
standard display relates to .
~ When the lighting is turned on . press the selector.
The number . operating mode and if applicable the name of the heating circuit that is
currently selected are shown in the lower part of the display .
~ Turn the selector to select a heating circuit.
Only heating circuits that exist in the system are displayed for selection .
~ Waita few seconds or press the selector .
The standard display refers to the heating circuit selected .
Table 4 Getting started - Heating circuit in the standard display
Lto.SOC
10
12 .5"
. pro.'~
'--'--- ' - Cl - Ql - (!) -- 1n -' ~ I I
6720 5' 2 n5-0~
4.2 Setting the operating mode
An explanation of the technical terms " operating mode ",
"automatic mode " and " optimised operation " can be found on
page 41 and 42 . Optimised operation is enabled by default.
There are no time programs for this operating mode . The
thermostatic valves/room thermostats control each room
individually so that heat is supplied individually , as required .
This avoids extended heat·up phases (e .g. following setback
mode) and allows for efficient operation .
~ Press the menu key to open the main menu .
~ Press the selector to open the Heltlne/Coollne menu .
~ Press the selector to open the Operltine mode menu .
~ If two or more heating circuits are installed. turn the selector to highlight Heltine
circuit
1. 2, 3 or 4 and press the selector.
~ Turn the selector to highlight Auto and press the selector.
~ Press and hold the Back key to return to the standard display .
All temperatures set in the currently valid time program for the heating system are
shown in a pOP ' up window in the lower part of the display . The currently valid
temperature flashes .
The user interface controls the room temperature according to the active time
program for the heating system .
--~---------------
Table 5 Getting started - Activating operating modes
rr.21.03.2014
Lto.SOC
Flow temperature
He, Pro, .' ~
12:35
10
12 .5"
6 7 20 5' 2 n S-03 .' 0
H PC400 - 6 720821983 (2017/07) 9

Bosch HPC 400 Specifications

General

Brand	Bosch
Model	HPC 400
Category	Control Panel
Language	English