Bosch PXY8 HC Series - 23.1 Setting up Home Connect; 23.2 Wi-Fi symbol; 23.3 Adding or removing a Wi-Fi home network; 23.4 Changing settings via the Home Connect app

en HomeConnect
18
The HomeConnect app guides you through the entire
login process. Follow the instructions in the HomeCon-
nect app to configure the settings.
Tips
¡ Please consult the documents supplied by
HomeConnect.
¡ Please also follow the instructions in the HomeCon-
nect app.
Notes
¡ Please note the safety precautions in this instruction
manual and make sure that they are also observed
when operating the appliance via the HomeCon-
nect app.
→"Safety", Page2
¡ Hobs are not designed to be left unattended. Al-
ways monitor the cooking process.
¡ Operating the appliance on the appliance itself al-
ways takes priority. During this time it is not possible
to operate the appliance using the HomeConnect
app.
¡ In networked standby mode, the appliance requires
a maximum of2W.
23.1 Setting up HomeConnect
Requirements
¡ The appliance is connected to the power supply and
is switched on.
¡ You have a mobile device with a current version of
the iOS or Android operating system, e.g. a smart-
phone.
¡ The mobile device and the appliance are within
range of your home network's Wi-Fi signal.
1.
Download the HomeConnect app.
2.
Open the HomeConnect app and scan the follow-
ing QR code.
3.
Follow the instructions in the HomeConnect app.
23.2 Wi-Fi symbol
The Wi-Fi indicator on the main screen changes ac-
cording to the status and quality of the connection and
the availability of the HomeConnect server.
status Description
Lights up steadily at half
brightness.
No network connection
saved.
Flashes at full brightness. Network connection is be-
ing established.
Lights up steadily at full
brightness.
Network connection
saved and Wi-Fi active.
status Description
Flashes. Network settings are re-
set.
Switched off. Network not active.
23.3 Adding or removing a Wi-Fi home
network
The following overview shows how to add or remove a
Wi-Fi home network.
Wi-Fi home network
status
Action
No Wi-Fi home network
stored.
To add the Wi-Fi home
network, briefly press ⁠.
The Wi-Fi home network
has now been saved.
To pair another appliance,
press and hold ⁠.
The Wi-Fi home network
has now been saved.
To reset the Wi-Fi home
network settings, press
and hold . If flashes,
press and hold again.
23.4 Changing settings via the
HomeConnect app
You can use the HomeConnect app to change the set-
tings for the cooking zones and send them to the hob.
Requirement:The hob is connected to the Wi-Fi and to
the HomeConnect app.
1.
Select the setting in the HomeConnect app and
send it to the hob.
Follow the instructions in the HomeConnect app.
Settings that you send from the HomeConnect app
to the hob must be confirmed on the hob.
a As soon as cooking settings are transmitted to a
cooking zone, the display starts to flash, depending
on the setting.
2.
Press to confirm the setting.
3.
To discard the setting, press any other touch field
on the hob.
23.5 Activating automatic presence
detection
1
Thanks to the automatic presence detection function,
you no longer need to confirm parameters on the hob
from your mobile device, provided you are near the
hob. If you send settings to a cooking zone, you can
confirm these directly from your mobile device.
Requirements
¡ The hob is connected to the Wi-Fi and to the
HomeConnect app.
¡ The Bluetooth is connected to the mobile device.
¡ The user is near the hob.
1.
Open the HomeConnect app.
2.
In order to set the automatic presence detection, fol-
low the instructions in the HomeConnect app.
1
Available depending on software version. Further information on availability can be found on the website.